Important!
If the food processor is to be used to chop different types of
food (e.g. raw meat followed by vegetables, or egg followed by
fruit), you must wash the parts that come into contact with food
between each type of food.
USING THE BLENDER
• The blender cannot be used unless the
mixing bowl (17) and mixing bowl lid (16) are
in place. Fit the mixing bowl onto the mixing
bowl shaft (7), and put the lid on the bowl.
The long plastic tongue must sit outside the
bowl on the side of the bowl turned out
towards the rear of the base. Turn the lid
anti-clockwise until it locks into place.
• Remove the safety cover (5) from the
blender shaft (6), if it is fitted.
• Fit the blender onto the blender shaft with
the handle at a backwards angle towards
the left, and turn it anti-clockwise until it
locks into place.
• Place the food in the blender.
• Fit the blender lid (3) by placing it over the
blender with the pin to the right of the
blender handle and turning the lid clockwise
until it locks into place.
• Fit the cap (4) onto the lid by placing it over
the lid so the pins of the measuring cup fit
into the holes in the lid, and turning the
measuring cup clockwise.
• Start the food processor.
• If you want to add more ingredients as you
go along, stop the food processor before
you remove the cap to avoid splashes.
• If you need to scrape inside the blender, wait until the blade
has stopped completely before you remove the lid! Use the
spatula (10), never your fingers.
• Remove the blender lid and the blender in reverse order. Press
the release button (1) while untwisting the lid.
• Important! We do not recommend using the blender to crush
ice cubes or frozen berries.
USING THE MIXING BOWL
• The mixing bowl cannot be used unless the safety cover is
fitted over the blender shaft. Fit the safety cover by placing it
over the blender shaft and turning it anti-clockwise.
• Fit the mixing bowl as described above.
• Fit the required accessory:
- To use the blade, remove the plastic cover (12) from the
blade and fit it on the accessory shaft (11). Place the
accessory shaft with the blade fitted onto it on the mixing
bowl shaft in the middle of the mixing bowl. Place the food in
the blender.
- To use the grating/slicing disc (15), fit
it onto the accessory shaft with the cutting
blade you are going to use facing
upwards. Place the accessory shaft with
the grating/slicing disc fitted onto it on the
mixing bowl shaft in the middle of the
mixing bowl. Check that it is fitted
correctly.
• Fit the mixing bowl lid as described
above.
• Start the food processor.
• When using the grating/slicing disc, feed the ingredients in
through the feed tube using the pusher (14). The same applies
if you need to add more ingredients when using the blade.
• If you need to scrape inside the mixing bowl, wait until the
blade has stopped completely! Use the spatula, never your
fingers.
• Remove the mixing bowl lid, blade, grating/slicing disc,
accessory shaft and mixing bowl in reverse order.
STORAGE
Ensure that the food processor is clean and dry before storing.
CLEANING
• Before cleaning, remove the plug from the wall socket.
• The best way to clean the base of the food processor is with a
slightly dampened cloth and, if necessary, a little detergent.
The base must not be submerged in any form of liquid.
• The blender, mixing bowl and all other loose parts can be
washed up as usual and are dishwasher-safe.
• Do not use any kind of strong or abrasive cleaning agent on
the food processor or accessories. Never use a scouring
sponge or similar to clean the food processor, as the surface
may be damaged.
ENVIRONMENTAL TIPS
Once any electrical product is no longer functional, it should be
disposed of in such a way as to cause minimum environmental
impact, in accordance with the regulations of your local authority.
In most cases you can take such products to your local recycling
station.
GUARANTEE TERMS
The guarantee does not apply:
• if the above instructions are not followed
• if the appliance has been interfered with
• if the appliance has been mishandled, subjected to rough
treatment, or has suffered any other form of damage
• if faults have arisen as a result of faults in your electricity
supply.
Due to the constant development of our products in terms of
function and design, we reserve the right to make changes to the
product without prior warning.
IMPORTER
Adexi Group
We cannot be held responsible for any printing errors.
11
IM6 09/05/05 13:49 Side 11