Filter
Top Products
PAGE 20 — MVH-R60H— OPERATION AND PARTS MANUAL — REV. #1 (09/09/04)
l
MVH-R60H — MAINTENANCE
NOITCEPSNIENIGNE.7ELBAT
)launaMenignEetarapesees,sliatedroF(
metI noitarepOfosruoH
leufroliofoegakaeL
sruoh8yrevE
)yliaDkcehC(
sdaerhtgninetsaffossenthgiT )yliaDkcehC(sruoh8yrevE
kcehclioenignE
tnemhsinelperdna
)yliaDkcehC(sruoh8yrevE
)level.xamdeificepsothsinelpeR(
tnemhsinelperlioenignE sruoh001yreveneht,sruoh02tsriF
gninaelcrenaelcriA sruoh05yrevE
NOITCEPSNIENIHCAM.6ELBAT
metI noitarepOfosruoH skrameR
)kcehcgnitratS(
sruoh8yrevE
)yadyreve(
tsolrodenesooL
swercs
sruoh8yrevE
)yadyreve(
trapynafoegamaD
sruoh8yrevE
)yadyreve(
gnillortnocfonoitcnuF
trapmetsys
sruoh8yrevE
)yadyreve(
ciluardyhfokaeL
metsys
sruoh001yrevE .12egapeeS
kcehcliorotarbiV sruoh003yrevE .22egapeeS
tnemecalperliorotarbiV sruoh001yrevE .22egapeeS
kcehcliociluardyH
neht,sruoh002tsriF
.srh0001yreve
.32egapeeS
kcehc)hctulc(tleb-V sruoh002yrevE .22egapeeS
Inspection and Maintenance Service Tables.
To make sure your plate compactor is always in good working
condition before using, carry out the maintenance inspection in
accordance with Tables 5 through 7.
These inspection intervals are for
operation under normal conditions.
Adjust your inspection intervals
based on the number hours plate
compactor is in use, and particular
working conditions.
EUQROTGNINETHGIT.5ELBAT
retemaiD)mc/gk.ni(
lairetaM
mm6 mm8 mm01 mm21 mm41 mm61 mm81 mm02
T4 07 051 003 005 057 001,1 004,1 000,2
T8-6 001 052 005 008 003,1 000,2 007,2 008,3
T11 051 004 008 002,1 000,2 009,2 002,4 006,5
*
001
)mm6(
053~003
)mm8(
007~056
)mm01(
)munimulafositrap-retnuocesacnI(*
.wercsdna,tlobhcaenodekramsilairetamfoytilauqdnalairetaM
dednahthgirllaeraenihcamsihthtiwesunisdaerhT:etoN
Fuel piping and connections should
be replaced every 2 years.
Daily Service
z
Check for leakage of fuel or oil.
z
Check for loose screws including tightness. See Table 7
below (tightening torque ), for retightening:
z
Remove soil and clean the bottom of compaction plate.
z
Check hydraulic pump, piping and hose for any leakage. A
loosened hydraulic hose can be a cause for leakage. Check
hydraulic hose connections with wrench applied for
tightness.
z
Check engine oil, see Inspection section.
CAUTION - General Maintenance Safety
Maintenance
Inspection and other services should
always
be carried out
on hard and level ground with the engine shutdown.
NOTE
NOTE