Filter
Top Products
Installation and Owner’s Guide 13
Connect the Electrical Components
AC Operation 120 volts AC voltage
(108 volts min. - 132 volts max.)
DC Operation 12 volts DC voltage
(model 323 only) (11.5 volts min. - 15.4 volts max.)
This refrigerator operates on both AC and DC electrical sources.
Operation out of these limits may damage the refrigerator’s
electrical circuit parts and will void the warranty.
WARNING: The rear of the refrigerator cooling system
has hot surfaces and sharp surfaces that can damage
electrical wiring. Make sure that there is a good clearance
between all electrical wiring and the cooling system of the
refrigerator. Position any electrical wiring within the
refrigerator enclosure opposite the burner side of the
refrigerator. Do not put any electrical wiring through the
roof exhaust vent. Failure to correctly position electrical
wiring can result in electrical shock or fire.
Reverse the Door Swing (optional)
This refrigerator has a door hinge that allows you to change the
direction that the door opens. You can change the door swing at
any time, but the best time is before you install the refrigerator.
To change door swing:
1. Remove the door (See Art00949):
- Turn out and save the upper hinge pin [1].
- Open the door [2] a small amount and pull the top of the
door away from the upper hinge of the refrigerator.
- Lift the door off of the lower hinge pin [3].
- Turn out, remove, and save the lower hinge pin.
2. Change the position of the hinges (See Art00950):
- Carefully pull the breaker [4] off the front of the refrigerator.
- Remove the screws [5] from the hinge [6] and the hinge
spacer [7].
- Invert the hinge and the hinge spacer and put them on the
other side of the refrigerator
- Attach the hinge and the hinge spacer with the screws.
- Turn the lower hinge pin down into the hinge.
3. Install the door:
- Put the door down onto the lower hinge pin.
- Close the door.
- Align the holes in the hinge and the door and hold in this
position.
- Invert the breaker and push it ontothe front of the refrigera-
tor.
Install the Refrigerator
WARNING: Make sure the seal strips [1] are not broken,
are completely around the refrigerator mounting flanges,
and are between the refrigerator mounting flanges and the
wall of the enclosure (See Art00951). If the seal is not
complete, exhaust fumes can be present in the living area
of the vehicle. The breathing of exhaust fumes can cause
dizziness, nausea, or in extreme cases, death.
1. Put screws through the refrigerator mounting flanges and into
the wall of the enclosure.
2. Put a cap on each of the screw holes in the refrigerator
mounting flanges.
3. Put screws through the braces [2] at the lower rear corners of
the refrigerator and into the floor (See Art00952).
- Make sure the distance from the floor level to the top of the
rough opening for the upper exhaust vent is at least 20 5/8
inches or poor cooling performance and damage to the
cooling system can occur.
- Make sure the distance from the floor level to the top of the
rough opening for the upper exhaust vent is at least 20 5/8
inches or poor cooling performance and damage to the
cooling system can occur.
- Align the upper exhaust vent horizontally above the
lower intake vent [1] of the refrigerator.
- Install a baffle [6] to prevent stagnant hot air in the area
above the refrigerator.
- Make sure the baffle is the full width of the inside of the
enclosure.
- If the distance from the back of the refrigerator to the wall of
the vehicle is more than one inch, install a baffle [7]
between the back of the refrigerator to the wall of the
vehicle.
- Turn the upper hinge pin down into the hinge and into the
door.
4. Examine the door:
- Make sure the door aligns correctly.
- Make sure the travel latch engages correctly.