Oster 6640 Blender User Manual


 
54
OSTERIZER® BLENDER PARTS AND CARE
COVER
The cover for your
O
STERIZER
®
B
LENDER
consists of two parts, the plastic feeder cap and the
vinyl cover. The cover is self-sealing, and is made of vinyl which is resistant to absorption
of odors and stains. The feeder cap is removable for use as a measuring cup and provides
an opening for the addition of other ingredients.
CONTAINER
The container (Diagram 1, Page 5) for the Blender is graduated for easy measurement and
is molded of heat and cold resistant material. (6640-Plastic; 6642-Glass; 6646-Glass)
The convenient handle and pouring lip permit easy removal of liquid mixtures while thicker
mixtures are more easily removed through the bottom opening.
PROCESSING ASSEMBLY
The processing assembly consists of three parts: (Diagram 2, Page 5) a sealing ring used
as a cushion between the container and the agitator; (Diagram 3, Page 5) an agitator of
high grade stainless steel; (Diagram 4, Page 5) a threaded container bottom.
MOTOR AND MOTOR BASE
The powerful multi-speed motor is the heart of the appliance and is designed just for this
unit. It is completely enclosed within the housing. The motor uses a “free-floating” feature
to reduce noise and wear. This allows the square post which protrudes from the motor base
to move slightly from side to side. The powerful food processing motor can be overloaded.
To avoid this possibility, closely follow the instructions in this book.
CARE AND CLEANING OF YOUR OSTERIZER® BLENDER
Blender container parts are corrosion resistant, sanitary and easily cleaned. Before first use
and after every use, separate container parts and clean thoroughly in warm, soapy water, then
rinse and dry well. DO NOT WASH ANY PARTS IN AN AUTOMATIC DISHWASHER.
Periodically check all parts before re-assembly. If the processing blades are stuck
or difficult to turn, DO NOT USE BLENDER. Check by carefully turning the blades
in a counterclockwise direction (opposite edges are sharp). Blades should turn freely.
If the container is chipped or cracked DO NOT USE BLENDER. Further use could result
in the container breaking during use. Use only recommended
O
STERIZER
®
B
LENDER
replacement parts
available at an Authorized Service Facility or the factory. USE OF
DAMAGED OR
NON-RECOMMENDED PARTS COULD RESULT IN SEVERE
PERSONAL INJURY
AND/OR DAMAGE TO THE BLENDER. See Page 5 for proper
container assembly and user instructions. NEVER IMMERSE THE MOTOR BASE IN
WATER. The housing can be cleaned with a damp cloth (unplug first). The motor is
permanently lubricated and does not require any additional lubrication. ANY SERVICING
SHOULD BE PERFORMED BY AN AUTHORIZED SERVICE FACILITY.
ASSEMBLING YOUR BLENDER
CAUTION: Follow these important steps to assemble, tighten, and mount Blender container
quickly and correctly. INJURY MAY RESULT IF MOVING BLADES ARE EXPOSED.
TIGHTENING THE CONTAINER
A. To tighten container bottom, put assembled
container securely into motor base ring with
handle and lug in front of the right stop.
B. Using container handle, turn container
to the left as far as possible. This insures
that the container bottom is tightened
properly. Remove container from motor
base and mount.
C. To operate Blender, place assembled
container in motor base ring with container
lug against flat side of the motor base stop.
If container lug does not rest against flat side
of right stop, remove container assembly
and place against flat side of left stop.
Seat container firmly and operate.
D. To remove container, lift straight up.
(If it is not easily removed, rock gently and
lift up, do not twist). If container bottom
cannot be loosened by hand, place
assembled container into motor base ring
with handle in front of left side stop.
Using handle, turn container to right
until container bottom loosens.
Do not attempt to place the container on or attempt to remove it from the motor base while
the motor is running.
ALWAYS HOLD CONTAINER WITH ONE HAND WHILE PROCESSING!
–1.50L–
–1.25L–
–1.00L–
–0.75L–
–0.50L–
–0.25L–
–4 –
–3 –
–2 –
–1 –
–5 –
–6 –
1
.5
0
L
1
.2
5
L
1
.0
0
L
0
.7
5
L
0
.
5
0
L
0
.
2
5
L
4
3
2
1
5
6
P
U
L
S
E
Speed
0
12345
67891
0
O
F
F
P
U
L
S
E
Speed
0
12345
67891
0
OF
F
1.50L
1.25L
1.00L
0.75L
0.50L
0.25L
4
3
2
1
5
6
1
.5
0
L
1
.
2
5
L
1
.0
0
L
0
.7
5
L
0
.
5
0
L
0
.2
5
L
4
3
2
1
5
6
P
U
L
S
E
S
p
e
e
d
0
12345
67891
0
O
F
F
1
.
5
0
L
1
.
2
5
L
1
.0
0
L
0
.7
5
L
0
.5
0
L
0
.2
5
L
4
3
2
1
5
6
P
U
L
S
E
Speed
0
12345
67891
0
O
F
F
AB
CD
1. 2. 3. 4.
1. Turn container upside down so the small
opening is at the top.
2. Place sealing ring on container opening.
3. Turn the agitator blades upside down and
place in mouth of container.
4. Thread container bottom to container.
R
IGHT
S
TOP
C
ONTAINER
L
UG
L
EFT
S
TOP