Filter
Top Products
DIAL MODELS WITH TIMER
PRESS POWER TO TURN THE BLENDER ON.
The blender is set to the food/drink selection identified
by a blinking indicator light. Turn dial to change the
food/drink selection.
Press START and blend ingredients to desired consistency.
Press STOP to stop the motor. (Pressing POWER
stops the motor and turns the blender off.)
Note: Food/drink selection can be changed during
blending by turning the dial to the desired selection.
Note: This blender is programmed to turn the
power off automatically if not used for a period
of several minutes.
To use PULSE, turn dial to desired food/drink selection.
Press PULSE and hold down
for desired length of time.
Release and allow blade to stop. Repeat cycle as desired.
To use Auto Blend
™
Timer, press BLEND TIME until
desired length of blending time (15, 30, 45, 60 seconds)
is illuminated.
Turn dial to desired food/drink selection.
Press START. Blender will automatically stop when
selected time has elapsed.
To stop blender before elapsed time, press STOP.
To use blender without timer, press BLEND TIME
until no lights are illuminated.
BLENDING TIPS
• Put liquids in the jar first, unless a recipe
says otherwise.
• Crushing ice: Crush 6 ice cubes or approximately
2 cups of ice at a time.
• This blender has been designed to gently process
foods when operating at low speeds. If blades do
not rotate during operation, simply choose a higher
speed.
• Do not remove the lid while in use. Remove feeder
cap to add smaller ingredients. (Figure 7)
• Cut all firm fruits and vegetables, cooked meats,
fish and seafood into pieces no lar
ger than 1/2 inch
(1.8 cm) to 1 inch (2.5 cm). Cut all kinds of cheeses
into pieces no larger than 1/2 inch (1.8 cm).
• This blender will not mash potatoes, whip egg
whites or substitute dair
y toppings, mix stif
f dough
or grind raw meat.
English 7English 6
FIGURE 1
FIGURE 2
TIGHTEN
LOOSEN
FIGURE 4
FIGURE 5
USING YOUR BLENDER
Clean blender according to the instructions in the
“Cleaning and Storing Your Blender” section.
Jar Assembly:
– Turn jar upside down so the small opening
is at the top.
(Figure 1)
– Place sealing ring over jar opening. (Figure 2)
– Place blade into jar. (Figure 3)
– Snap threaded bottom disc and collar together.
Place collar over blade and jar.
(Note: If there
are slots on top of collar, line them up with
notches on jar.)
Place the collar on jar and turn
the threaded bottom disc clockwise to tighten.
(Figure 4)
– Place jar assembly onto base. (Figure 5)
– Place ingredients into jar.
– Place lid with feeder cap on jar.
– Plug the power cord into a 120 Volt
AC electrical outlet.
PUSH BUTTON MODELS
Slide switch to HIGH or LOW (If your model does
not have a slide switch, push HIGH or LOW button.)
Push desired speed and blend ingredients to
desired consistency.
Push OFF to stop the blender and turn blender off.
To use PULSE, select HIGH or LOW. Push PULSE and
hold down for desired length of time.Release PULSE
and allow blade to stop. Repeat cycle as desired.
DIAL MODELS WITHOUT TIMER
Turn dial to desired food/drink selection.
Press ON and blend ingredients to desired
consistency.
Pr
ess OFF to stop the motor and tur
n blender of
f.
Note: Food/drink selection can be changed during
blending by turning the dial to the desired selection.
To use PULSE, turn dial to desired food/drink
selection. Press PULSE and hold down for desired
length of time. Release and allow blade to stop.
Repeat cycle as
desir
ed.
FIGURE 3
FIGURE 6
513665_core_blender_IB_REV.qxd 6/19/09 10:53 AM Page 6