Philips HD7810 Coffeemaker User Manual


 
8 Clean the pod holder after descaling to
prevent the sieve in the centre from getting
clogged.
Frost-free storage
If the coffee machine has already been used and
therefore has been ushed with water, it may only
be used and stored in a frost-free place to prevent
it from becoming damaged.
Replacement
You can order all removable parts from your Philips
dealer or a Philips service centre.
Environment
Do not throw away the machine with the
normal household waste at the end of its life,
but hand it in at an ofcial collection point for
recycling. By doing this, you help to preserve
the environment (Fig. 27).
Guarantee & service
If you need service or information or if you have a
problem, please consult the worldwide guarantee
leaet or visit our website at www.philips.com.
au or www.senseo.com. You can also contact the
Philips Customer Care Centre in your country;
they will be happy to help you.
For Australia Customer Service telephone:
Freecall™: 1800 794 329
You nd the telephone numbers for other
countries in the worldwide guarantee leaet.
If there is no Customer Care Centre in your
country, turn to your local Philips dealer or contact
the Service Department of Philips Domestic
Appliances and Personal Care BV. You nd
their address and fax number in the worldwide
guarantee leaet.
The purchase of the Philips SENSEO
®
coffee
machine does not exhaust any of the rights of Sara
Lee/Moccona or Philips under any of their patents
nor does it confer upon the purchaser a licence
under these patents.
Troubleshooting
If you have a problem, you may nd the solution in
the table below. If the table does not provide the
solution to your problem or if you have a question,
see the chapter ‘Guarantee & service’.
,
You can interrupt the brewing process at any
time by pressing the on/off button I. If you
switch the machine back on after you have
interrupted the brewing process, the machine
does not complete the interrupted brewing
cycle.
Do not remove the water reservoir during a
brewing cycle, as this causes the machine to draw
in air. When this happens, the next cup will only
be partly lled.
Note: If you only get a small quantity of coffee or
no coffee at all out of the machine, you have not
ushed the machine properly before rst use. As a
result, the boiler is not or not completely lled. Flush
the machine properly (see chapter ‘Preparing the
machine for use’) before you brew another cup of
coffee.
10 After use, lift the pod holder out of the
machine and remove the coffee pod(s).
Be careful when you do this, for there may still be
some water/coffee on the coffee pod(s).
Tips
Rinse the pod holders and the coffee spout
regularly to make sure that the coffee always
tastes optimally.
The SENSEO
®
coffee tastes best if you stir it
before you drink it.
If you intend to make another cup
of SENSEO
®
coffee later, just leave
the coffee machine switched on. The
machine automatically switches itself off after
1 hour. (Fig. 18)
Cleaning
Never immerse the SENSEO
\
coffee machine in
water.
Never clean the machine by ushing it with the
lid open.
1 Always unplug the machine before you clean
it.
2 Clean the outside of the machine with a
moist cloth.
3 Remove the coffee spout (Fig. 19).
You can disassemble the coffee spout for
more thorough cleaning. (Fig. 20)
4 Clean the coffee spout, the pod holders
and the drip tray in hot water, if necessary
with some washing-up liquid, or in the
dishwasher (Fig. 21).
5 Hold the cup tray in your hand while you
clean it with hot water, if necessary with
some washing-up liquid (Fig. 22).
You can also clean the cup tray in the dishwasher.
To clean the cup tray, always remove it from
the machine, as it might prove sharp when it is
handled incorrectly. Always handle it carefully.
6 Clean the pod holders in hot water, if
necessary with some washing-up liquid, or in
the dishwasher. (Fig. 23)
Make sure the sieve in the centre of the pod
holder is not clogged. If the sieve is clogged, unclog
it by rinsing the pod holder under a running tap.
If necessary, use a washing-up brush or a pin to
unclog the sieve.
7 Clean the water reservoir in hot water,
if necessary with some washing-up
liquid. (Fig. 24)
Note: You can remove the cover of the water reservoir
to clean the inside thoroughly.
Note: If you use a washing-up brush, be careful not
to damage the valve in the bottom of the water
reservoir.
-
,
,
,
,
8 Rinse the parts with fresh water after
cleaning and put them back into the machine.
9 Clean the water distribution disc with a moist
cloth (Fig. 25).
Be careful when you do this. Make sure that the
rubber sealing ring does not get stuck under the
edge of the water distribution disc. If it does, the
coffee machine starts to leak!
Flushing
If you have not used the coffee machine for three
days, ush it with fresh water before you use it
again.
Flush the machine in the following way:
1 Fill the water reservoir with cold water up to
the MAX indication and put it back onto the
machine. (Fig. 3)
2 Put the 1-cup pod holder ° or the 2-cup
pod holder °° in the machine without
pod(s). (Fig. 6)
3 Put a bowl (with a capacity of at least
1500ml) under the coffee spout to collect the
water. (Fig. 8)
4 Press the on/off button I and subsequently
press the 1-cup button ° and the 2-
cup button
°° briey at the same
time. (Fig. 9)
The machine lls itself with water from the water
reservoir. This takes some time and you will
probably not notice that this happens. After a while,
the machine starts to ush and switches itself off
after the ushing cycle.
Descaling
Regular descaling prolongs the life of the coffee
machine and guarantees optimal brewing results for
a long time. If you use the machine twice a day on
average, you must descale it once every 3 months.
1 Fill the water reservoir up to the MAX
indication with descaler and water according
to the instructions on the package of the
descaler. Then put the water reservoir back
onto the coffee machine. (Fig. 3)
Use a descaler based on citric acid.
2 Press on/off button I. (Fig. 10)
The machine is ready for use when the indicator
light burns continuously.
3 Place the 1-cup pod holder ° in the coffee
machine, preferably with a used coffee pod in
it. Close the lid and make sure it is properly
locked.
We advise you to put a used coffee pod in the
pod holder when you descale the machine. This
pod serves as a ‘lter’ to prevent the sieve in
the pod holder from getting clogged with scale
residues.
4 Put a bowl with a capacity of at least 1500ml
under the coffee spout to collect the mixture
of descaler and water. (Fig. 8)
5 Press the 2-cup button °° and let the
machine operate. Repeat this until the water
reservoir is empty. (Fig. 26)
Never descale the SENSEO
\
coffee machine
with the lid open. Make sure the lid is properly
locked.
6 Repeat steps 1 to 5 with a new mixture of
descaler and water.
7 Rinse the water reservoir with fresh water to
remove descaler residues. Flush the machine
with fresh water at least 3 times by repeating
steps 1 to 5.
Do not rell the water reservoir with used
hot water.
,
422200197772
4/6