Filter
Top Products
17
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
3ELBAT
llaWroiretxEsuoiraVrofderiuqeRstnenopmoCgnitneV
-stiKnoitanimreTesehTfoynAgnisUnehW,sessenkcihT
,)STH5.4VS(noitanimreTerauqS
)SSTH5.4VS(noitanimreTerauqSllamS
)RTH5.4VS(noitanimreTdnuoR
stnenopmoCgnitneV
deriuqeR
ssenkcihTllaWroiretxE
)mm(sehcni
ylnOtiKnoitanimreT4/19ot5)532ot721(
tnev.ni6dnatiKnoitanimreT
)6L5.4VS(noitces
4/19)943ot532(4/331ot
tnev.ni21dnatiKnoitanimreT
)21L5.4VS(noitces
)205ot004(4/391ot4/351
cipocseleTdnatiKnoitanimreT
.ni6dna)AL5.4VS(noitces
)6L5.4VS(noitcestnev
)725ot372(4/302ot4/301
H
H = 28 in. (711 mm) Maximum.
7 in. (178 mm)
*When using Secure Flex,
use Firestop/Spacer
SF4.5HF
*Wall Firestop/Spacer
(SV4.5HF)
H
H = 28 in. (711 mm) Maximum.
**Wall Firestop/Spacer
(SV4.5HF)
**When using Secure
Flex, use Firestop/Spacer
SF4.5HF
8³⁄₁₆ in. (207 mm)
H
*Wall
Firestop/Spacer
(SV4.5HF)
V
*When using Secure Flex,
use Firestop/Spacer
SF4.5HF
ELBATG
muminiMVmumixaMH
teef)m(teef)m(
1)503.0(5)25.1(
2)16.0(01)1.3(
3)419.0(51)56.4(
4)22.1(02)2.6(
.xaM)m4.21(teef04=H+V
.xaM)m2.6(teef02=H
H
V
**Wall Firestop/Spacer
(SV4.5HF)
**When using Secure
Flex, use Firestop/Spacer
SF4.5BF
*Ceiling
Firestop/Spacer
(SV4.5BF)
*When using Secure Flex,
use Firestop/Spacer
SF4.5HF
Figure 38
-
Top Vent - ONE 90 DEGREE ELBOW -
ELBOW CONNECTION AT APPLIANCE
Figure 39
-
Top Vent - ONE 90 DEGREE ELBOW -
ELBOW CONNECTION NOT DIRECTLY AT APPLIANCE
Figure 37
- Rear Vent - NO ELBOWS - for D-500 and DR-500 models
only - Small Square Horizontal Termination (SV4.5HTSS)
Figure 36
- Rear Vent - NO ELBOWS - Square Horizontal Termination
(SV4.5HTS)
See
Table 3
as an aid in venting component selection for a particular
range of exterior wall thicknesses.
See
Table 3
as an aid in venting component selection for a particular
range of exterior wall thicknesses.
See
Table 3
as an aid in venting component selection
for a particular range of exterior wall thicknesses.
HORIZONTAL VENT FIGURES/TABLES
Note: Secure Vent components (rigid vent
pipe and terminal) are shown in the figures;
Secure Flex components (flexible vent pipe
and terminal) may also be used.
Note: Two 45 degree elbows may be used in place
of one 90 degree elbow. The same rise to run ratios,
as shown in the venting figures for 90 elbows, must
be followed if 45 degree elbows are used.
Note: It is very important that the horizontal/
inclined run be maintained in a straight (no
dips) and recommended to be in a slightly
elevated plane, in a direction away from the
fireplace of
¹⁄₄
" rise per foot (20 mm per
meter) which is ideal, though rise per foot run
ratios that are smaller are acceptable all the
way down to at or near level.
Square termination (SV4.5HTS)
shown; Round Termination
(SV4.5HTR) may also be used.
Small Square termination
(SV4.5HTSS) may only be used
on DT-500 and D-500 models.
WARNING: UNDER NO CIRCUM-
STANCES MAY SEPARATE SECTIONS
OF CONCENTRIC FLEXIBLE VENT
PIPE BE JOINED TOGETHER.
Round Termination (SV4.5HTR) may not be used.
Round Termination (SV4.5HTR) may not be used.
Square termination (SV4.5HTS)
shown; Round Termination
(SV4.5HTR) may also be used.
Small Square termination
(SV4.5HTSS) may only be used
on DT-500 and D-500 models.
See
Table 3
as an aid in venting component selection for a particular
range of exterior wall thicknesses.
Note: SV4.5BF (Secure Vent), SF4.5BF (Secure
Flex) firestop/spacer must be used anytime vent
pipe passes through a combustible floor or
ceiling. SV4.5HF (Secure Vent), SF4.5HF (Se-
cure Flex) firestop/spacer must be used anytime
vent pipe passes through a combustible wall.
ELBATF
wobleeerged09en0=V
.xaM)m419.0(teef3=H