Tribest FS-610 Juicer User Manual


 

Silicone parts tips
Silicone parts are able to be washed. Dry the parts after washing. Please check if the
silicone parts are placed correctly.
*Juice might be leaking if you do not place the silicone correctly.
<Silicone brush>
Face down the tail of silicone brush and put it in
like the picture next to it.
<Silicone Extraction>
After washing, put the silicone in correctly with
arrow in the picture.
<Silicone Ring>
Silicone ring can be washed. Put the silicone ring
back to the place properly.
Bigger silicone side, face up and place it
correctly.
5*1
Silicone parts are able to be disassembled and washed. Fully dry the silicone parts after
washing. Please check if the silicone parts are placed correctly.
*Juice may leak if you do not assemble the silicone parts properly.
<Silicone Wiper Blade>
Hold the Head portion (1 in the drawing) of
the silicone blade and slide downward to the
middle of the blade slot, then pull outward.
2. Assemble
Insert the Head portion into the blade slot
in the middle of the bracket, slide the Head
upward. Insert the Tail portion into the blade
slot in the middle of the bracket, slide the Tail
downward.
1. Disassemble
Hold the Tail portion (2 in the drawing) of the silicone blade and push upward
to the middle of the blade slot, then pull outward.
<Pressure Plug of Auger Housing>
After washing, put the Pressure Plug in correctly
as shown in the picture.
Sealing Ring can be easily disassembled by
pushing from the bottom side of the Auger
Housing (smaller silicone ring) for easy clean-
ing. After it is thoroughly dried, put the sealing
ring properly back in its place. Push the sealing
ring (with the larger side facing up) back in
place from the inside of the Auger Housing.
<Sealing Ring of the Auger Housing>
Tips for silicone parts
TIPS FOR SILICONE PARTS
Note
Please read before the extraction.
Inserting the food one by one could extract properly
ber materials(celery or water parsley) into right amount to get the good
result(4-5inch). For better result, cut the material by 1inch and insert one by one.
ⴚ
erent fruits with a lot of moisture to get more
ber. Please cut carrot into quarters before
erent amount of juice to
extract.)
If the food is not fresh, the amount of juice will be less. To get more juice, dip it in the
clean water until the material gets wet. Then, the food will have more juice to be extract.
ⴜ
Some food does not have juice that can be extracted.
ⴝ
While in use, the appliance might be making a noise. However, the appliance has no
problem with operation.
ⴞ
There might be a kick-back from the extraction of fruits and vegetables. Be aware.
Materials like Peach, Plum, or persimmon need to be removed the seed. Defrost
frozen fruits and you use with milk or beverages slowly.
Please read before juice extraction.
1. Feed the foods into the Feeding Chute piece by piece in order to properly
extract juice without clogging.
optimal results. For even better results, cut the foods to a width of 1 inch and
insert the pieces one by one.
3. When extracting carrot juice, please cut carrots into halves or quarters in
4. While in use, the appliance may make a noise. This does not constitute that
the appliance has a problem with operation.
5. You must remove seeds from foods such as peaches and plums.
6. Fully defrost frozen fruits when you make frozen fruit sorbet. Feeding hard
frozen fruit may damage the juicing system.
7. Do not overfeed to avoid clogging the machine.
8. Some portion of grounded fruit or vegetable may splash out occasionally if
the plunger is not in use.
Tips for extracting
TIPS FOR EXTRACTING