Filter
Top Products
About the controls on the refrigerator.
9 IS COLDEST
0 IS OFF
5
8
9
4
3
2
1
0
6
7
5
8
9
4
3
2
1
6
7
Your controls will look like one of the following:
Startup Steps for Proper Temperature Control
STEP 1—Set Fresh Food Control on “5.”
STEP 2—Set Freezer Control on “5.”
STEP 3—WAIT 12 HOURS for temperature to stabilize.
STEP 4—If a change is needed, move the control one number at a time
and allow 12 hours for temperature to stabilize.
NOTE: Turning the refrigerator to the
0
(off) setting via the controls does
not shut off electrical power to the refrigerator.
Control settings will vary based on personal preferences, usage
and operating conditions and may require more than one adjustment.
0 IS OFF
9 IS COLDEST
FREEZER
REFRIGERATOR
Energy Smart™ Override
Press the Energy Smart™ pad for 3 seconds to override the
Energy Smart™ feature. The LED above the pad will flash
multiple times to confirm a successful override of the feature.
This will disable the feature from altering the performance of
your unit for 18 hours. Eighteen hours after the feature has been
disabled, the Energy Smart™ feature will continue normal
operation.
To Change Temperature Control Setting with Touch Pads:
• Freezer setting is on the left side of the display.
• Refrigerator setting is on the right side of the display.
— Press the Warmer or Colder pad for compartment and direction
desired.
— Present control setting number will illuminate.
— Each time the pad is touched, compartment setting changes one
number.
A display of 1 is warmest and 9 is the coldest setting.
To Turn Cooling Off:
To stop cooling in the refrigerator and freezer compartments,
first repeatedly press the Warmer pad for the freezer until its
display continuously flashes “1”. Then, using the refrigerator
control, repeatedly press Warmer until both displays flash “0”.
“0” in both displays turns off the cooling system. On some
models, it may be necessary to set only one control to 0 to
turn off cooling in both compartments.
NOTE: Turning the refrigerator to the
0
(off) setting via the
controls does not shut off electrical power to the refrigerator.
Control settings will vary based on personal preferences, usage
and operating conditions and may require more than one adjustment.
The temperature controls are preset in the factory at 37°F for the
refrigerator compartment and 0°F for the freezer compartment.
Allow 24 hours for the temperature to stabilize to the preset
recommended settings.
The temperature controls can display both the SET temperature as well
as the actual temperature in the refrigerator and freezer. The actual
temperature may vary slightly from the SET temperature based on usage
and operating environment.
Setting either or both controls to OFF stops cooling in both the freezer
and refrigerator compartments, but does not shut off electrical power
to the refrigerator.
NOTE: The refrigerator is shipped with protective film covering the
temperature controls. If this film was not removed during installation,
remove it now.
9 IS COLDEST
0 IS OFF
FREEZERFRESH FOOD
5
8
9
4
3
2
1
0
6
7
5
8
9
4
3
2
1
6
7
6
About Energy Smart™ Models Controls
Energy Smart™ is located on the controls of models
equipped with the feature, as shown in the image.
What Energy Smart™ Does
If the ACM (Appliance Communication Module) is
connected to your refrigerator and is receiving
utility rate information, then Energy Smart™
feature alters the performance of the refrigerator. It
minimizes energy consumption when directed by the
Nucleus
TM
(separately purchased device) or Smart
Meter. The Energy Smart
TM
feature can cause
changes in refrigerator or freezer compartment
temperatures and can cause changes in the rate of
ice cube production.
Locking the Dispenser
(on some models)
Press the Lock pad
for 3 seconds to lock the
dispenser and control panel.
To unlock, press and hold
the key pads again for 3 seconds.