Filter
Top Products
16
Style 2 Series Electronic Oven Control (see “Electronic
Oven Controls” section)
To Set a Timed Cook:
1.
Press BAKE. The bake indicator light will light up.
2.
Set the temperature (optional).
3.
Press the TEMP/TIME “up” or “down” arrow pad to enter a
temperature other than the one displayed.
4.
Press COOK TIME. The cook time oven indicator light will
light up.
5.
Press TEMP/TIME “up” or “down” arrow pad to enter the
length of time to cook.
6.
Press START/ENTER. The display will count down the time.
When the time ends, the oven will shut off automatically and
“End” will appear on the display.
7.
Press OFF or open the oven door to clear the display.
To Set a Delayed Timed Cook:
Before setting, make sure the clock is set to the correct time of
day. See “Clock” section.
1.
Press BAKE.
2.
Set the temperature (optional).
3.
Press the TEMP “up” or “down” arrow pad to enter a
temperature other than the one displayed.
4.
Press COOK TIME. The cook time oven indicator light will
light up.
5.
Press the TEMP/TIME “up” or “down” arrow pad to enter the
length of time to cook.
6.
Press START TIME. The start time/delay oven indicator light
will light up.
7.
Press the TEMP/TIME “up” or “down” arrow pad to enter the
time of day to start.
8.
Press START/ENTER.
When the start time is reached, the oven will automatically
turn on. The temperature and/or time settings can be
changed any time after pressing START/ENTER by repeating
steps 1-7. When the set cook time ends, the oven will shut off
automatically and “End” will appear on the display.
9.
Press OFF/CANCEL or open the oven door to clear the
display.
Sequence Programming
(on some models)
Sequence Programming allows you to program at one time up to
four cook functions, and is usable with other electronic oven
control functions, such as the Timer and Warming Drawer.
Sequence Programming takes precedence over any
nonsequenced cook function. For example, if an untimed Bake
function is in process and a sequence program is started, the
untimed Bake function will be canceled, and the program
sequence will start.
All steps of a sequenced program must be programmed with a
stop time. If a stop time is not entered for a step in the sequence
program, and the FIRST/NEXT STEP pad is pressed, three tones
will sound.
To Program the First Step of the Sequence:
1.
Press FIRST/NEXT STEP.
“PROGRAM” and “STEP” will appear on the display. A
flashing “1” will also appear on the display, indicating that
step 1 is being programmed.
2.
Choose the desired cook function by pressing any cook
function key.
3.
Press START TIME, then HR and MIN “up” or “down” arrow
pads to set the time of day for the first cook function to begin.
If START TIME is not pressed, then the sequence of cook
functions will begin immediately once programming is
complete and START is pressed.
The display will show either the time of day (if start time was
not programmed) or the start time (if same was programmed),
but with a flashing colon. “Stop” and “Time” will also appear
on the display.
4.
Press STOP TIME, then HR and MIN “up” or “down” arrow
pads to set the time of day for the first cook function to stop.
To Program Next Steps of the Sequence:
1.
Press FIRST/NEXT STEP.
“PROGRAM” and “STEP” will appear on the display. The
number of the steps being programmed will flash.
“START” and “TIME” will appear on the display.
2.
Choose the desired cook function by pressing any cook
function key.
Press TEMP “up” or “down” arrow pad (if desired) to select
temperature.
3.
Press STOP TIME, then HR and MIN “up” or “down” arrow
pads to select stop time.
4.
Press START to begin sequence.
5.
Press OFF/CANCEL at any time to clear program and to stop
program.
To Review/Modify Programmed Sequence:
If program steps are partially or completely programmed, yet the
sequence has not been started, the programmed cook functions
can be reviewed.
1.
Press REVIEW STEPS. Step 1 will appear in the display
Subsequent presses of REVIEW STEPS will cause display of
programmed steps in order.
“STEP” and “RECALL” will appear on the display. The
number of the displayed step will flash. A recalled step will
remain lit on the display for 5 minutes if no further action is
taken.
2.
If fewer than four steps have been programmed, press
REVIEW STEPS repeatedly until the last programmed step is
displayed, then press FIRST/NEXT STEP if it is desired to
program an additional step.
While a step is recalled, a cook function pad can be used to
change the function, or the TEMPERATURE “up” or “down”
arrow pad can be used to change the set temperature.
START TIME, when used with the HR or MIN “up” or “down”
arrow pads, can be used to change, add or delete a delayed
start.
STOP TIME can be used to change the stop time. Changing
the stop time of a step will automatically change the start
times and stop times of all subsequent programmed cook
functions.
3.
After Review/Modification of the programmed sequence is
complete, press START to begin sequence.