Filter
Top Products
Common dishwashing problems
PROBLEM
CAUSED BY
SOLUTION
--m-w
Spottlng and
fllmlng
Hard water
Water is not
hot enough
Not enough
detergent. or
improper detergent
“0ld”detergent
Improper loading
No rinse aid
AIR DRY Setting used
Fill detergent dispensers to capacity. Use dishwasher de-
tergent with highest available phosphorus content May
be necessary to install water softener.
Water temperature should be at least 140°F (60°C). Set
water heater thermostat to a higher setting. Run water at
sink until hot before starting and/or use HI-TEMP WASH
Option.
Use more dishwasher detergent. Use detergent with high-
est available phosphorus content...especially with hard
water.
Use only fresh, dry dishwasher detergent. Store tightly
closed box, in cool, dry place. Discard old, lumpy deter-
gent. Do not fill dispensers until ready to start dishwasher.
Make sure dishes and glassware are loaded so spray
reaches all surfaces and items drain properly. Do not ov-
erload. Do not nest items.
Make sure large items do not block spray from reaching
detergent dispensers.
Does the rinse aid dispenser need filling? See instructions
on page 7.
To remove spots and film, try a vinegar rinse...
I. Wash and rinse load as usual. Use AIR DRY.
2. Remove all metal items.
3. Put 2 cups (500 mL) white vinegar in a container on the
bottom rack.
4. Run dishwasher through a complete washing cycle.
Drying without heat may result in some spotting of glasses
and silver.
I_---.
--m-m.
Small particles
Spray arm or arms not
Check spray arms to make sure they turn freely after load-
deposlted on rotating freely
Items
ing. Be sure a utensil has not prevented their turnrng.
“0ld”detergent Use only fresh, dry dishwasher detergent. Store tightly
closed box in cool, dry place. Discard old, lumpy deter-
gent. Do not fill dispensers until ready to start dishwasher.
Not enough
Use more dishwasher detergent. Use detergent with high-
detergent, or
est available phosphorus content...especially with hard
improper detergent water.
Water is not hot
Water temperature should be at least 140°F (60°C). Set
enough
water heater thermostat to a higher setting. Run water at
sink until hot before starting and/or use HI-TEMP WASH
Option.
Water pressure may
If water pressure is low, do not use water for other purposes
be low, dishwasher is
while drshwasher is running [to assure correct fills).
not filling properly
----
Dlshes not dry
Water is not hot
Water temperature should be at least 140’: (60°C). Set
enough
water heater thermostat to a higher setting. Run water at
sink until hot before starting and/or use HI-TEMP WASH
Option.
Improper loading
Make sure dishes and glassware are loaded so spray
reaches all surfaces and items drain properly Do not ov-
erload. Do not nest.
No rinse aid
Fill rinse aid dispenser.
AIR DRY Setting used
Allow more time when using AIR DRY Option, or use HEAT
DRY. Plastic items may need towel drying.
-_.__l__ _~
Black marks on
Aluminum utensils
Use care In loadlng alumlnum utensils, especially any
china or white rubbing against items
llghtwelght loll container. Place so they do not touch
utensils
during washing dlshes. Remove black marks with plastic scouring pad
and a mild abrasive cleanser
--
--._---
Chlpplng or
breaking
Improper loading Do not overload. Load glasses in the top rack only. Load
glassware
between prongs, not over them. Glasses loaded over
prongs will not be supported and may chip or break.
12
--I--^I.-.‘Pn.me.w
-.7.--e..
--^- ,.=.._.-._ _ .._____ _- -,-._-_
-___.___..__.I I ____.