Whirlpool GGE388LXS Range User Manual


 
18
When the self-clean cycle ends:
“CLN COMPLETE will scroll in the selected oven text area. After
5 seconds, “OVEN COOLING” will scroll in the display until the
oven temperature falls below 500°F (260°C).
“UNLOCKING” will be displayed until the oven door unlocks and
the lock icon turns off.
To Delay Start Self-Clean:
Before delay starting Self-Clean, make sure the oven door is
completely closed or it will not lock and the cycle will not begin.
1. Press START TIME.
“PRESS (^) FOR UPPER OVEN” will scroll in the upper text
area, and “PRESS ( ) FOR LOWER OVEN” will scroll in the
lower text area.
2. Press the Temp/Time “up” or “down” arrow pads to select the
desired oven.
“--:--” will be displayed, and “Set starting time. Push START”
will scroll from right to left in the selected oven text area for
2 minutes or until the Temp/Time “up” or “down” arrow pads
are pressed again.
3. Press the Temp/Time “up” or “down” arrow pads until the
desired time is reached.
“Select cooking/cleaning mode” will scroll in the selected
oven text area for 2 minutes or until a cooking cycle is
selected.
4. Press STEAM/PRECISE CLEAN option.
“PRESS ^ FOR UPPER OVEN” will scroll in the upper oven
text area and “PRESS FOR LOWER OVEN” will scroll in the
lower oven text area.
5. Press the Temp/Time “up” or “down” arrow pads to select the
desired oven.
“REMOVE RACKS” will scroll in the selected oven text area
for 5 seconds, followed by “SELECT OPTION.” In the lower
oven text area, “PRESS ^ or KEY” will scroll from right to
left.
6. Press the Temp/Time “up” arrow pad. “Precise CLEAN”
appears in the upper text display area, and “Push START”
appears in the lower text display area.
7. Press START.
“Set clean time or Push Start” appears in the upper text
display area.
8. Press the Temp/Time “up” or “down” arrow pad until the
desired cleaning time is displayed.
9. Press START.
10. “UNLOCK IN XXX” will scroll in the upper or lower text area
(depending on oven selection). “LOCKING” will scroll until the
door is locked.
After the door is locked, “CLEAN UPPER” or “CLEAN
LOWER” will scroll in the selected oven text area until the
clean cycle is finished.
When the self-clean cycle ends:
“CLN COMPLETE will scroll in the selected oven text area. After
5 seconds, “OVEN COOLING” will scroll in the display until the
oven temperature falls below 500°F (260°C).
“UNLOCKING” will be displayed until the oven door unlocks and
the lock icon turns off.
SteamClean
(on some models)
The SteamClean feature is designed for light oven cavity bottom
cleaning on models that have hidden bake in both ovens.
Allow the range to cool to room temperature before using the
SteamClean feature. If your oven cavity is above 100°F (38°C),
OVEN COOLING will appear in the display and the SteamClean
feature will not activate until it cools down.
Remove all racks and accessories from the oven cavity.
For best results, use 4 oz (118 mL) of distilled or filtered water.
The SteamClean feature will take a total of 20 minutes. A
beep will sound at the end of the cycle.
IMPORTANT: Because the water in the oven bottom is hot, do
not open the oven door during the SteamClean cycle.
Press CANCEL/OFF at any time to end the cycle. The display will
return to the time of day.
Helpful Hints
Once the SteamClean cycle is complete, remove all
remaining water in the bottom of the oven with a sponge or
cloth.
Wipe any remaining moisture from the oven door interior,
oven cavity interior sides, and cooktop.
Use a soft brush or nylon scrubber to wipe the oven interior.
This may help with more stubborn stains.
It is recommended to use distilled or filtered water, as tap
water may leave mineral deposits on the oven bottom. Use a
cloth soaked with vinegar or lemon juice to remove any
mineral deposits that may be left after the SteamClean cycle.
If the oven is heavily soiled, use the Self-Clean cycle. The
SteamClean cycle may be used first to eliminate most of the
debris, resulting in a more effective self-clean.
To SteamClean:
1. Remove all rack and accessories from the oven cavity.
2. Press STEAM/PRECISE CLEAN option.
3. “Press ^ for Upper Oven” will scroll in the upper text area and
“Press for Lower Oven” will scroll in the lower text area.
4. Press the Temp/Time “up” or “down” arrow pads to select the
desired oven.
5. “REMOVE RACKS” will scroll in the selected oven text area,
followed by “SELECT OPTION.” In the other text area, “Press
^ or key” will scroll from left to right.
6. Press Temp/Time “down” arrow pad.
7. “Steam CLEAN” is displayed in the upper text area, and
“Push START” is displayed in the lower text area.
8. Press START.
“Open door pour 10 Oz water to oven base and push START”
will scroll in the lower text area.
9. Open the oven door of the selected oven and pour 10 oz of
distilled or filtered water to the oven bottom. Then close the
oven door.
10. Press START.
“STEAM CLEAN” is displayed in the upper text area.
11. After 20 minutes, a beep will sound to signal the end of the
cycle.
12. Press CANCEL for the selected oven to clear the display.
13. Remove any excess water with a sponger or cloth and wipe
down oven interior. If needed, use a non-scratch copper
scrubbing pad to remove stubborn soils.
^
^
^
^
^