Filter
Top Products
6
Display
When power is first supplied to the microwave oven, a “:” will
blink in the display. Touch OFF CANCEL to stop the blinking.
If the “:” blinks in the display at any other time, a power failure
has occurred. Touch OFF CANCEL and reset the clock if needed.
If an invalid value has been entered, the invalid entry tones will
sound, and the input prompt will reappear in the display. Retry
your entry.
When the microwave oven is in use, the display shows cooking
power, quantities, weights and/or prompts. When the microwave
oven is not in use (standby mode), the display shows the time of
day or Timer countdown.
The speed of the scrolling text may be adjusted, if necessary.
To Adjust Scroll Speed:
1. Touch and hold CLOCK for 3 seconds until 2 tones sound.
2. Touch number pad “1” for SLOW, “2” for NORMAL or “3” for
FAST.
3. Touch START to complete the adjustment.
Start
The START pad begins any function. If it is not touched within
5 seconds after touching a pad, “PRESS START” will scroll in the
display as a reminder. If START pad is not touched within
2 minutes after touching a pad, the display will return to the time
of day mode and the programmed function will be canceled.
If cooking is interrupted by opening the door, touching START will
resume the preset cycle.
Off Cancel
The OFF CANCEL pad stops most functions except for the
Control Lock.
The microwave oven will also turn off when the door is opened.
Close the door and touch START to resume the cycle.
Clock
This is a standard 12-hour clock (12:00-11:59) and does not
show a.m. or p.m.
To Set:
The microwave oven and timer must be off.
1. Touch CLOCK.
2. Touch the number pads to set the time of day.
3. Touch CLOCK or START.
To Remove:
1. Touch CLOCK.
2. Touch 0.
3. Touch CLOCK.
The time will disappear, and “:” will appear on the display.
Tones
Tones are audible signals, indicating the following:
One tone
■ Valid entry (short tone)
Two tones
■ End of stage in multistage cooking
■ Control Lock active
■ Hidden feature has been entered or exited
■ Reminder, repeat each minute after the end-of-cycle tones
Three tones
■ Invalid entry
Four tones
■ End of cycle
To Turn Off/On Valid Entry Tones: With the microwave oven in
standby mode, touch and hold the number pad “1” for 3 seconds
until 2 tones sound. Touch and hold number pad “1” to turn tones
back on.
To Turn Off All Tones (except hidden feature tones): With the
microwave oven in standby mode, touch and hold the number
pad “2” for 3 seconds until 2 tones sound. Touch and hold
number pad “2” to turn tones back on.
Control Lock
The Control Lock shuts down the control panel pads to prevent
unintended use of the microwave oven.
When the control is locked, only the Vent Fan and Light pads will
function. If any other control pad is touched, “LOCKED” will
appear in the display and the invalid entry tones will sound.
To Lock/Unlock Control: The microwave oven must be in
standby mode. Touch and hold OFF CANCEL for 3 seconds until
2 tones sound and a padlock icon appears in the display. Repeat
to unlock and remove the padlock icon from display.
Vent Fan
The vent (exhaust) fan has 2 speeds: high and low.
To protect the microwave oven, if the temperature from the range
or cooktop below the microwave oven gets too hot, the vent fan
will automatically turn on at high speed. It may stay on for up to
1 hour to cool the microwave oven. When this occurs, the vent
fan cannot be turned off. If the vent fan pad is touched during
automatic fan operation, “AUTO FAN IS ON, FAN SPEED WILL
REMAIN ON UNTIL HEAT IS NO LONGER SENSED” will scroll in
the display as a reminder.
The vent fan is also the cooling fan, and will start at low speed
when any cooking function begins. It will remain on until the
cooking function ends.
To Turn Vent Fan On/Off: Touch VENT FAN pad once for high,
twice for low or 3 times for off.
Cooktop Light
The cooktop light has 3 settings: high, low and off.
To Turn Light On/Off: Touch LIGHT pad once for high, twice for
low or 3 times for off.