Filter
Top Products
I
I’ I
I
II
I
B
n
OVEN MUST BE CONNECTED WlTH
A. Where local codes
permit...
connecting of the cabinet-grounding
conductor to the neutral (white) junction
box wire:
cable from
junction
power supply
Now start...
WI oven in kitchen.
1
I Remove shipping materials, tape,
and protective film from oven. Do Not
remove shipping base at this time.
2
m Remove the racks and other parts
from inside the oven. Remove the air grille
taped to the top or side of oven.
COPPER WIRE ONLY.
C
n
Wire sizes and connections must
conform to the requirements of the National
Electrical Code, ANSI/NFPA 70 - latest
edition’, and all local codes and
ordinances. Wire sizes and connections must
conform with the rating of the appliance.
Copies of the standards listed may be
obtained from:
‘Nattonal Fire Protection
AssociationBatterymarch Park
Qulncy, Massachusetts 02269
Personal Injury Hazard
l
Use both hands to remove oven doors.
l
Grasp only the sides of oven doors.
l
Do Not use handle or any portion of
the front frame or trim for lifting.
. Because of the weight and size of the
ovens, two or more people are
needed to move and safely install the
ovens.
Failure to property grasp the oven
doors or to lift ovens properly could
result in damage to the product or
personal injury.
D
I This appliance should be
connected directly to the fused
disconnect (or circuit breaker box)
through flexible, armored or non-metallic
sheathed, copper cable (with grounding
wire). The flexible armored cable from the
appliance should be connected directly
to the junction box.
Grounded Neutral
1. Disconnect the power supply.
2. Remove the terminal block cover.
3. Connect together 3 wires: green and
white appliance cable wires and the
neutral (white) wire in junction box.
4. Connect the two black wires together;
then connect the two red wires
together with wire connectors. See
Figure 1.
B. Where local codes Do
Not permit...
connecting the cabinet-grounding
conductor to the neutral (white) junction
box wire:
cable from
junction
Dower sur>tAv
n
Locate the junction box to allow as
much slack in the cable as possible
between the junction box and the
appliance so that the oven can be
moved if servicing is ever necessary.
Do Not cut the condult.
n
A U.L.-listed conduit connector must
be provided at the junction box.
G
n
A wiring diagram is included in the
Tech Sheet. The Tech Sheet is located
behind the control panel.
Electrical
rlres
connection
I Insert a nail (or equivalent, 5/32”
diameter item) into the hole in each of the
hinges. Close the door as far as possible.
Lift the oven door off of the hinges. Set
aside.
Figure 2
cable
conduit
tram
connector
oven
Ungrounded neutral
1. Disconnect power supply.
2. Separate the green and white
appliance cable wires.
3. Connect the white appliance cable
wire to the neutral (white) wire in the
junction box.
4. Connect the two black wires together;
then connect the two red wires
together with wire connectors. See
Figure 2.
5. Connect the green or bare grounding
wire from the appliance cable to a
grounded wire in the junction box.
C. If connecting to a four-
wire electrical s
r
stem...
Do Not connect the cab net-grounding
conductor to the neutral (white) junction
box wire.
cable from
junction
power supply
ElecMcalShockHazc~d
l
Electrical ground is required on thls
appliance.
l
Do Not connect to the electrical supply
until appliance is permanently
grounded.
l
Disconnect power to the junction box
before making the electrical
connection.
l
lhii appliance must be connected to a
grounded, metallic, permanent wiring
system, or a grounding connector
should be connected to the grounding
terminal or wire lead on the appliance.
Failure to do so could result in a fire,
personal injury or electrical shock.
Before movlng ovens across floor, check
that ovens are on shipping base or slide
ovens onto cardboard or hardboard.
Failure to follow these instructions may
result in damage to floor covering.
4
n
Disconnect power supply. Move
oven close to final position. Remove and
discard shipping base, cardboard or
hardboard. Feed appliance cable
through the opening in cabinet. Make
electrical connection. See “Electrical
requirements” and -Electrical connection”
sections, Panels A and B.
This appliance is manufactured with white
(neutral) power supply wire and a
cabinet-connected green grounding wire
twisted together.
Connect the appliance cable to the
junction box through the U.L.-listed conduit
connector. Complete electrical
connection according to local codes and
ordinances.
4 ~black wires
Figure 3
&FL-My
cable
from
connector
5
n
Lift oven up into cabinet cutout
using the oven opening as an area to grip.
-
oven
1. D&connect the power supply.
2. Separate the green (or bare) and white
appliance cable wires.
3. Connect the white appliance cable
wire to the neutral (white) wire in the
junction box.
4. Connect the two black wires together;
then connect the two red wires
together with wire connectors. See
Figure 3.
5. Connect the green appliance cable
wire to the green grounding wire in the
junction box.
Panel B