Filter
Top Products
Removing meat drawer
and cover
Models TTl6CK and TT18CK
To remove:
1. Slide meat drawer out to the guide stops.
2. Lift the front of meat drawer until it clears
stops. Slide drawer out the rest of the
way.
3. Lift cover straight up and out.
To replace:
1. Fit notches in cover sides over center
shelf support.
2. Lower cover into place.
3. Fit edges of drawer into supports on
cover.
4. Slide meat drawer into place.
Models TT20AK and TTPOBK
To remove:
1. Slide meat drawer out to the guide stops.
2. Lift the front of meat drawer until it clears
stops.
3. Slide drawer out the rest of the way.
4. Tilt cover front up.
5. Lift up at back until it releases.
6. Pull straight out. (Be careful-glass is
heavy!)
To replace:
1. Guide rear hooks of cover into the shetl
supporl slots.
2. Tilt rover front up until hooks drop into
slots. Lower front of cover to a level
position.
3. Replace meat drawer in reverse order.
Removing trivet and cover
Models TTl4EK and lTl8EK
The trivet can be removed for easier
cleaning.
To remove trivet:
1. Lift front of cover frame and remove
cover support.
2. Lift trivet from the support brackets on
the back wall.
3. Replace in reverse order. Be sure to
replace trivet with higher edge toward
rear of refrigerator.
To remove cover:
1. Lift front and remove cover support.
2. Lift cover up and out.
To replace cover:
1. Fit cover notches into supports on walls
of refrigerator. Lower front into place.
2. Insert cover support (with the long tab
toward the front) into the groove on the
underside of the crisper cover.
NOTE: If the support needs adjustment,
turn base clockwise to raise; counter-
clockwise to lower. (See diagram below.)
Removing crispers and
crisper cover
Models lT14CK and lT16DK
To remove:
1. Slide crisper straight forward to the guide
stops.
2. Lift front until it clears stops. Slide crisper
out the rest of the way.
3. Replace in reverse order.
To remove cover:
I. Lift front and remove cover support.
2. Lift cover up and out.
To replace cover:
1. Fit cover notches into supports on walls
of refrigerator. Lower front into place.
2. Insert cover support (with long tab
toward the front) into the groove on the
underside of the crisper cover.
NOTE: If the support needs adjustment,
turn base clockwise to raise; counter-
clockwise to lower the support. (See
diagram above.)
Models lT16CK and lTl8CK
To remove crispers:
1. Slide crisper straight forward to the guide
stops.
2. Lift front until it clears stops. Slide crisper
out the rest of the way.
3. Replace in reverse order.
To remove cover:
1. Push up glass insert from the bottom,
then slide out with both hands. (Be
careful-the glass is heavy!)
2. Lift front of arver frame and remove
cover support.
3. Lift cover frame by pulling up and out.
To replace cover:
1. Fit cover notches into supf~~ts on
Walk
of refrigerator. Lower cover into place.
2. Insert cover support (with long tab tpward
the front) into the groove on the
underside of the crisper.
NOTE: lf the support needs adjustment,
turn base dockwise to raise; counter-
clockwise to lower the support. (See
diagram at left.)
3. Slide back of glass insert into place; then
lower the front.
Models lT2OAK and lT2OBK
To remove crispers:
1. Slide crisper straight forward to the guide
stops.
2. Lift front until it clears stops. Slide crisper
out the rest of the way.
3. Replace in reverse order.
To remove cover:
1. Push up glass insert from the bottom,
then slide out with both hands. (Be
careful-the glass Is heavy!)
2. Lift front of cover frame by pulling up and
out.
3. Remove horizontal metal cover support
bar.
To replace cover:
1. Replace metal cover support bar on wall
supports in front section of cabinet.
2. Fit back corners of cover frame into
notch supports on walls of refrigerator.
then lower into place.
3. Slide back of glass insert into place; then
lower the front.
Removing freezer shelf
Models lTl6CK, lT16DK, lT1 BCK,
TTSOAK and m2OBK
To remove:
1. Lift front slightly.
2. Lift back off supports.
3. Replace in reverse order.
Removing the base grille
Models ll2OAK and ITSOBK
To remove:
1. Open the refrigerator door.
2. Pull grille outward.
3. Do Not remove Tech Sheet fastened
behind grille.
To replace:
1. Line up grille support tabs with metal
clips.
2. Push firmly to snap into position.
3. Close the refrigerator door.
Page 7