Cuisinart DGB-300 Coffee Grinder User Manual


 
PROGRAMMING YOUR
COFFEEiWAKER
1. Setting the Clock:
M%en the coffeemaker is plugged in,
12:OO
will
flash continuously until you set the time.
Entering “Set lime” Mode:
‘Ih
set the time, hold down either the Hours or
iMinutes button until the clock stops flashing and
begins to count up (about 2 seconds). You are now
in the
“‘Time
Set” mode and can operate either but-
ton to achieve the desired setting. The buttons can
hc held down to scroll through
the
digits or pressed
and released lightly to advance one
dlglt
at a time.
\&Then
scrolling, the numhers will advance slowly at
first and then speed up to the rate of about three
per second. When the
number
displayed approach-
es the desired setting, release the
hutton
and press
r+eatedly
to advance one digit at a time. Be careful
to make sure that
the
PM indicator is on if a PM
time is
desired.
Exiting “Set Time” Mode:
The “Time Set” mode can he exited in
one of two ways:
1. Press anv button besides the Hours or Minutes
button.
Th’;s
will exit the “Time Set” and activate
the selected function.
2.
Do
nothing. If neither the Hours nor Minutes
button is pressed for a period of five seconds, the
“Time Set” mode is exited.
2. Setting the Program Time:
To
Start Program Feature:
To
set
the unit to make coffee at the programmed
time, press the “Program” button and release it.
The green light next to the button will light. The
coffeemaker will start to
brew
at the l~rogrammed
time.
If no time appears when the
hutton
is pressed and
the green light turns off at the release of
the
but-
ton, it means that no program time has
been
set.
The “Programmed” mode cannot he entered mitil
the
Program time has
been
set.
Entering “Set Program Time” Mode:
Press and hold the Program Set
button
(about 2
seconds) until the green light hegins to flash. This
signals that
you
have
entered
the “Set Program
‘lime” mode.
‘I‘he
desired time can be set by press-
ing the Hours and Minutes buttons to scroll
for-
bard
through the digits. Pressing and holding
either
hutton
will allow you to scroll
continuousl!;
slowly at first, and accelerate to the r3te of about
three digits per second.
As
the desired time setting
approaches, release the button and then press
repeatedly to advance one digit at a time.
Exiting “Set Program Time” Mode:
“Set Program Time” may he exited in any
of three ways:
1. Press the Program Set button. ‘l’his will cause
the coffeemaker to revert to its previous state. If it
was OFF, it will return to the OFF position. If
“Programmed”, it will revert to this state, and
so on. This is a safety feature.
2. Press any other button (except Hours or
Minutes). “Set Program Time”
will
be exited and
the function of that
hutton
will he executed.
3.
Do nothing. If neither the Hours nor Illinutes
button is pressed for a period of
fire
seconds,
the
“Set Program Time” mode is exited and the pro-
grammed setting will he in effect.
PROGRAMMING
AUTOMATIC-OFF TIME
‘1%~
Automatic-Off time can he programmed
anywhere from immediate shut off after completion
of the
I)rey
cycle to four hours.
U’hen
the
coffeemaker shuts itself off, two tones will sound.
Four hours is the default time.
The
0:OO
setting
shuts the unit off immediately after brewing is
complete.
‘Ii)
check the current setting, press and
hold the On/Off button and the Automatic-Off
time is displayed.
To change the preset time, press and hold the
On/Off
hutton
until the red “power” light begjns to
flash. This signals that you have entered the “Set
Automatic-Of?
mode. Press
the
Hours and
hlinutes
buttons to scroll forward through the digits
until desired time appears. Thus, the first
setting