Filter
Top Products
15
IMPORTANT: Never try
to slice soft cheese like
mozzarella or hard cheese
like Parmesan. You may
damage the slicing disc or
the food processor itself.
You can successfully shred
most cheeses except soft
ones. The exception is
mozzarella, which shreds
well if thoroughly chilled.
Hard cheeses like
Parmesan shred well only
at room temperature.
Therefore, only attempt
to slice or shred mozzarella
when well chilled, and
Parmesan when at
room temperature.
TECHNIQUES
FOR KNEADING
YEAST DOUGH
WITH THE
POWERPREP
®
METAL DOUGH
BLADE
The PowerPrep Plus
®
Food Processor is
designed to mix and knead
dough in a fraction of the
time it takes to do it by
hand. You will get perfect
results every time if you
follow these directions.
NEVER TRY TO
PROCESS DOUGH
THAT IS TOO STIFF TO
KNEAD COMFORTABLY
BY HAND.
There are two general
types of yeast dough.
Typical bread dough is
made with a flour mix that
contains at least 50% white
flour. It is uniformly soft,
pliable and slightly sticky
when properly kneaded.
It always cleans the inside
of the work bowl complete-
ly when properly kneaded.
Typical sweet dough
contains a higher propor-
tion of sugar, butter and/or
eggs than typical bread
dough. It is rich and sticky
and it does not clean the
inside of the work bowl.
It requires less kneading
after the ingredients
are mixed. Although
30 seconds is usually
sufficient, 60 to 90 seconds
gives better results if the
machine does not slow
down. Except for kneading,
described below, the
processing procedures and
use of the DOUGH button
are the same for both types
of dough.
Machine capacity
Recommended maximum
amount of flour is 6 cups
of all-purpose flour or
3-1/2 cups of whole-grain
flour. If a bread dough calls
for more than the recom-
mended amounts of flour,
mix and knead it in equal
batches. Do the same for
sweet doughs that call for
more than 3-1/2 cups
of flour.
Using the right blade
Use the metal dough blade
when the recipe calls for
more than 3-1/2 cups
(17-1/2 ounces) (875 ml)
of flour. Use the metal
chopping blade when a
recipe calls for less than
3-1/2 (875 ml) cups of flour.
Because the metal dough
blade does not extend to
the outside rim of the
work bowl, it cannot pick up
all the flour when small
amounts are processed.
Measuring the flour
It’s best to weigh it. If you
don’t have a scale, or the
recipe does not specify
weight, measure by the stir,
scoop and sweep method.
Use a standard, graduated
dry measure, not a liquid
measuring cup.
With a spoon or fork, stir
the flour in its container. Do
not measure flour directly
out of the bag; it is too
packed to get an accurate
measure. With the dry
measure, scoop up the
flour so it overflows. With
a spatula or knife, sweep
excess flour back into the
container so the top of
the measure is level.
Do not pack flour into
the dry measure.
Proofing the yeast
The expiration date is
marked on the packages.
To be sure your yeast is
active, dissolve it in a small
amount of warm liquid
(about 1/3 cup [75 ml] for
one package of dry yeast).
The temperature of liquid
used to dissolve and
activate yeast must be
between 105 and
120F(40C and 48C). Yeast
cells are not activated at
temperatures lower than
this and they die when
exposed to temperatures
higher than 130F (54C).
If the recipe includes a
sweetener like sugar or
honey, add a teaspoon
with the yeast. If no
sweetener is called for, add
a pinch, or add a pinch of
flour. The yeast won’t foam
without it. Let the mixture
stand until it foams, up to
10 minutes.