Filter
Top Products
2
2
Getting Started
Before operating the cooktop, clean the
glass ceramic surface carefully as outlined
in the Care and Cleaning Instructions. The
cooktop surface must be free of any foreign
substances, especially those that could melt
and permanently adhere to the glass.
During the first uses of your new cooktop, you
may smell a slight burning odor or see light
smoke. Both of these conditions are normal in
new glass ceramic cooktops.
Heating Elements
DACOR glass ceramic cooktops contain ribbon
type radiant heating elements in various sizes to
allow the user the greatest cooking flexibility.
The Ribbon Radiant Heaters illuminate within
approximately 3-4 seconds of activation. The
Dual Element consists of two elements which
may be operated simultaneously for heavy
cooking demands. The inner element may be
operated alone for improved simmering with
smaller utensils.
All elements feature temperature limiters to
ensure that the safe operating temperature of
the glass ceramic top is never exceeded.
DACOR glass ceramic cooktops operate by
automatically cycling the heating elements
between “off” and full power. As the numeric
setting of the control is increased, the element
will stay at full power for longer periods and at
zero power for shorter durations.
When the element is set to the dual range, both
the inner and outer elements will cycle on and
off at the same time. (The outer heating element
can never be operated alone.)
For maximum performance from any burner
remember to closely match heating element
diameters and cookware size.
Residual Heat Indicator Lights
All Dacor glass cooktops have element residual
heat indicator lights. These indicating lights
remain illuminated until the burner cools down to
a safe temperature of 140º degrees.
IMPORTANT:
Be certain that the cookware and glass
surfaces are clean and dry before you turn
on the burner and place a pot or pan on the
heating burner.
Element ON Indicator Light
One light indicating power is on to any of the
elements.
Setting the Controls
NOTE:
When at its highest setting, the heating
element may cycle off due to the protection
of the temperature limiter built into each
element. This temperature limiting occurs
automatically to prevent exceeding the
maximum allowable surface temperature and
to maintain the constant desired heat level.
The element will cycle back on after it has
cooled to a safe temperature.
ETT Models
To turn an element on, tap the “ON/OFF” key
then tap the up arrow for the desired element.
The element will come on at a setting of “5” and
may be adjusted up or down by pressing the
appropriate key.
To activate the Dual Element, tap the “ON/OFF”
key then tap the Dual Element Indicator to
activate the outer ring of the element. It will
come on at a setting of “5”, then tap the up
indicator for desired temperature setting.
To turn an element off, tap the “ON/OFF” key.
You may turn off all active elements at the same
time by tapping twice on the Dacor logo located
below the controls.
ETT Secure Lockout
To avoid accidentally turning the cooktop on
while cleaning it, activate the “Secure Lockout”
feature.
To lock out the cooktop:
Press and hold the DACOR logo for 3-4
seconds and the cooktop will be secured from
use. You will hear three beeps and a light will
illuminate directly above the DACOR logo
indicating that the cooktop is secure. The control
panel is now disabled and may be cleaned
without activating any functions.
To unlock the cooktop:
Press and hold the DACOR logo for 3-4
seconds. You will hear three beeps and the light
will go out. The control panel is now ready for
use.
NOTES:
1. For maximum safety, the cooktop
will be in the “lock out” mode when
first installed, or whenever power
is interrupted. Follow the “Unlock”
instructions above to reactivate the
control panel.
2. To turn off multiple burners all at one
time - tap the Dacor logo twice.
6 1/2"
1200W
7 3/4"
1800W
5 1/2"
1000W
7"
1500W
9 3/4"
2400W
Model ETT304
Top View
7"
1500w
7 3/4"
1800w
9"
2100w
6 1/2"
1200w
9 3/4"
2400w
5 1/2"
1000w
Model ETT365
Top View
CER Models
Push down and turn the knob to the desired
temperature setting. The control knobs can be
turned either clockwise or counterclockwise
to the desired temperature setting. The knob
that controls the Dual Element may be pushed
down and turned counter-clockwise to heat the
single inner element or clockwise to heat both
the inner and outer elements. All knobs may
be positioned below setting #1 to achieve the
lowest temperatures possible.
OFF
12
11
10
9
8
7
6
5
4
3
2
1
OFF
12
11
10
9
8
7
6
5
4
3
2
1
OFF
12
11
10
9
8
7
6
5
4
3
2
1
OFF
12
11
10
9
8
7
6
5
4
3
2
1
7"
1800W
5 1/2"
1000W
5 1/2"
1000W
7 1/2"
2000W
9"
2000W
Model CER304
Top View
ETT304/ETT365 Controls