Filter
Top Products
4
Power Supply Requirements
It is the owner’s responsibility to ensure that a licensed •
electrician performs the installation of the electrical sup-
ply for this appliance. The electrical installation, includ-
ing minimum supply wire size, must comply with the
National Electric Code ANSI/NFPA 70 (latest revision)
and local codes and ordinances.
A copy of this standard may be obtained from:
The correct voltage, frequency and amperage must be •
supplied to the appliance from a dedicated, grounded,
single phase circuit that is protected by a properly sized
circuit breaker or time-delay fuse. If a time-delay fuse is
utilized, fuse both sides of the line (L1 and L2).
The required voltage, frequency and amperage ratings •
are listed on the appliance data plate (see page 3) and
in the table for reference.
Preheat times and cavity temperature recovery times •
will be increased slightly if operating the unit with less
than a 240 Vac circuit.
This appliance is provided with electrical wiring in a •
flexible metal conduit.
Product Specifications
Model
Number
Dedicated Circuit
Requirements*
Total Connected
Load
EORS127
240 Vac 60 Hz,
30 Amp.
5.0 kW
(20.8 Amp.)
MORS127
EORS130
MORS130
EORS136
EORS227
240 Vac 60 Hz,
50 Amp.
10.0 kW
(41.7 Amp.)
EORD227
MORS227
MORD227
EORS230
EORD230
MOCS230
MOCD230
* The above specifications are for reference only. See the
appliance data plate (page 3) for exact specifications.
National Fire Protection Association
1 Batterymarch Park
Quincy, Massachusetts 02269-9101
Model
Number
Overall
Width (A)
Chassis
Width (B)*
Overall
Height (C)
Chassis
Height (D)
EORS127/
MORS127
26 7/8”
(68.3 cm)
25 3/8”
(64.5 cm)
28 7/16”
(72.2 cm)
26 7/16”
(67.2 cm)
EORS130/
MORS130
29 7/8”
(75.9 cm)
28 3/8”
(72.1 cm)
EORS136
35 7/8”
(91.1 cm)
34 3/8”
(87.3 cm)
28 5/8”
(72.7 cm)
26 5/8”
(67.6 cm)
EORX227/
MORX227
26 7/8”
(68.3 cm)
25 3/8”
(64.5 cm)
49 15/16”
(127.0 cm)
47 15/16”
(121.8 cm)
EORX230/
MORX230
29 7/8”
(75.9 cm)
28 3/8”
(72.1 cm)
X = Number of convection ovens, see page 3
* Width at light covers on sides
Product Dimensions
All tolerances: +1/16 (1.6 mm). -0, unless otherwise stated.
Utility
Cutout
Width (E)
Utility
Cutout
Height (F)
Utility
Cutout
Depth (G)
Control
Panel
Depth (H)
Notch
Depth (J)
Chassis
Depth (K)
Notch
Height (L)
All Models
5”
(12.7 cm)
5 ¼”
(13.3 cm)
6”
(15.2 cm)
1”
(2.54 cm)
1 1/8”
(2.9 cm)
24”
(61.0 cm)
1 1/8”
(2.9 cm)