Filter
Top Products
106828-01D
For more information, visit www.desatech.com
For more information, visit www.desatech.com
19
19
TO TURN OFF GAS
TO APPLIANCE
1. Set ON/OFF switch located on rear cover to “OFF”.
2a. Open lower panel.
2b. If Using Optional Hand-Held Remote: Set selector switch in
the OFF position to prevent draining battery.
3. Turn off all electrical power to the appliance if service is to
be performed.
4. Push in gas control knob slightly and turn clockwise
to “OFF”.
5. Close lower panel.
Shutting Off Burners Only (pilot stays lit)
You may shut off the burners and keep the pilot lit by doing one
of the following:
1. Turn control knob clockwise to the PILOT position.
2. Set selector switch in the OFF position.
OPERATING STOVE WITH
B-VENT BURNER SYSTEM
WARNING: If you do not follow these instructions
exactly, a fire or explosion may result causing prop-
erty damage, personal injury or loss of life.
A. This appliance has a pilot which must be lighted by hand.
When lighting the pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all around the appliance area
for gas. Be sure to smell next to the floor because some gas
is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone in
your building.
• Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier's instructions.
C. Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by hand,
don't try to repair it, call a qualified service technician. Force
or attempted repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system
and any gas control which has been under water.
FOR YOUR SAFETY
READ BEFORE LIGHTING
LIGHTING
INSTRUCTIONS
1. STOP! Read the safety information above.
2. Set ON/OFF switch located on rear cover to “OFF”.
3. Open lower panel.
4. Turn off all electric power to the burner system.
5. Push in gas control knob slightly and turn clockwise
to “OFF”.
6. Wait five (5) minutes to clear out any gas. Then smell for
gas, including near the floor. If you smell gas, STOP! Fol-
low “B” in the safety information above. If you don't smell
gas, go to the next step.
7. The pilot is located by the main burner and should not re-
quire accessing for lighting.
8.
Turn knob on gas control counterclockwise to
“PILOT”.
9. Push in control knob all the way and hold. Immediately light
the pilot by repeatedly depressing the piezo spark ignitor un-
til a flame appears. Continue to hold for about one (1) minute
after the pilot is lit. Release knob and it will pop back. Pilot
should remain lit. If it goes out, repeat steps 5 through 8.
Figure 48 - Control Valve
Gas Control Knob
Piezo Ignitor
•
If knob does not pop up when released, stop and im-
mediately call your service technician or gas supplier.
• If the pilot will not stay lit after several tries, turn the gas
control knob to “OFF” and call your service technician
or gas supplier.
10. Turn gas control counterclockwise to “ON”.
11. Turn on all electric power to the burner system.
12. Turn the ON/OFF switch to ON position.
13. Close lower panel.
OPERATING STOVE WITH B-VENT BURNER SYSTEM
For Your Safety Read Before Lighting
Lighting Instructions
To Turn Off Gas To Appliance
Manual Lighting Procedure
MANUAL LIGHTING
PROCEDURE
1. Remove glass door (see Removing/Replacing Glass Door,
page 17).
2. Follow steps 1 through 8 under Lighting Instructions, page 19.
3. Depress control knob and light pilot with match.
4. Keep control knob pressed in for 30 seconds after lighting
pilot. After 30 seconds, release control knob. Now follow steps
10 through 13.
5. Replace glass door (see Removing/Replacing Glass Door,
page 17).