Filter
Top Products
13
Connecting the Water Supply
Before Installing The Water Supply Line, You Will Need:
s "ASIC4OOLSADJUSTABLEWRENCHmATBLADE
screwdriver, and Phillips
TM
screwdriver
s !CCESSTOAHOUSEHOLDCOLDWATERLINEWITHWATER
pressure between 30 and 100 psi.
s !WATERSUPPLYLINEMADEOFINCHMM/$
copper or stainless steel tubing. To determine the
length of tubing needed, measure the distance
from the ice maker inlet valve at the back of the
refrigerator to your cold water pipe. Then add
approximately 7 feet (2.1 meters), so the refrigerator
can be moved out for cleaning (as shown).
s !SHUTOFFVALVETOCONNECTTHEWATERSUPPLYLINE
to your household water system. DO NOT use a
self-piercing type shutoff valve.
s !COMPRESSIONNUTANDFERRULESLEEVEFORCONNECTING
a copper water supply line to the ice maker inlet valve.
To Connect Water Supply Line To Ice Maker Inlet Valve
1. Disconnect refrigerator from electric power source.
2. Place end of water supply line into sink or bucket.
Turn ON water supply and flush supply line until
water is clear. Turn OFF water supply at shutoff valve.
3. Remove plastic cap from water valve inlet and
discard cap.
4. If you use copper tubing - Slide brass compression
nut, then ferrule (sleeve) onto water supply line. Push
water supply line into water valve inlet as far as it will
GOINCHMM3LIDEFERRULESLEEVEINTOVALVE
inlet and finger tighten compression nut onto valve.
Tighten another half turn with a wrench; DO NOT
over tighten. See Figure 1.
If you use stainless steel tubing - The nut and
ferrule are already assembled on the tubing. Slide
compression nut onto valve inlet and finger tighten
compression nut onto valve. Tighten another half turn
with a wrench; DO NOT over tighten. See Figure 2.
5. With steel clamp and screw, secure water supply line
(copper tubing only) to rear panel of refrigerator as shown.
6. Coil excess water supply line (copper tubing
only), about 2½ turns, behind refrigerator as
shown and arrange coils so they do not vibrate or
wear against any other surface.
7. Turn ON water supply at shutoff valve and tighten
any connections that leak.
8. Reconnect refrigerator to electrical power source.
9. To turn ice maker on, lower wire signal arm (side
MOUNTEDORSETTHEICEMAKERS/N/FFPOWER
switch to the “I” position (rear mounted).
Figure 1 Figure 2
!
"#
$!
#
%
WARNING
To avoid electric shock, which can cause death or
severe personal injury, disconnect the refrigerator
from electrical power before connecting a water
supply line to the refrigerator.
CAUTION
To Avoid Property Damage:
s #OPPEROR3TAINLESS3TEELBRAIDEDTUBINGIS
recommended for the water supply line. Water
supply tubing made of ¼ inch plastic is not
recommended to be used. Plastic tubing greatly
increases the potential for water leaks, and the
manufacturer will not be responsible for any
damage if plastic tubing is used for the supply line.
s $/./4INSTALLWATERSUPPLYTUBINGINAREAS
where temperatures fall below freezing.
s #HEMICALSFROMAMALFUNCTIONINGSOFTENER
can damage the ice maker. If the ice maker
is connected to soft water, ensure that the
softener is maintained and working properly.
IMPORTANT
Ensure that your water supply line connections
comply with all local plumbing codes.
NOTE
Check with your local building authority for
recommendations on water lines and associated materials
prior to installing your new refrigerator. Depending on
your local/state building codes, Electrolux recommends for
homes with existing valves its Smart Choice® water line kit
5305513409 (with a 6 ft. Stainless Steel Water Line) and for
homes without an existing valve, Electrolux recommends
its Smart Choice water® line kit 5305510264 (with a 20 ft.
Copper Water Line with self-tapping saddle valve). Please
refer to www.frigidaire.com/store for more information.
IMPORTANT
!FTERCONNECTINGTHEWATERSUPPLYREFERTOh(OWTO0RIME
the Water Supply System” for important information
about priming an empty water supply system.
Your refrigerator’s water supply system includes
several tubing lines, a water filter, a water valve, and
a water tank. To ensure that your water dispenser
works properly, this system must be completely
filled with water when your refrigerator is first
connected to the household water supply line.