Stovax RV55 Range User Manual


 
21
LEGAL REQUIREMENTS
Before installation of this product please read these
instructions fully.
It is very important to understand the requirements of the national
Building Regulations* and standards**, along with any local
regulations and working practices that may apply. Should any
conflict occur between these instructions and these regulations
then the regulations must apply.
Your local Building Control Office can advise regarding the
requirements of the regulations.
The appliance must be fitted by a registered installer†, or
approved by your local building control officer.
Works must be carried out with care to meet the requirements of
Health and Safety‡ and comply with the Health and Safety rules,
and any new regulations introduced during the lifetime of these
instructions.. Particular attention should be drawn to:
•Handling: The appliance is heavy. Adequate facilities
must be available for loading, unloading and site handling.
•Fire Cement: Some fire cement is caustic and must not
come into contact with the skin. Protective gloves must be
worn. Wash hands thoroughly with plenty of water after
contact with skin.
•Asbestos: This appliance contains no asbestos. If there
is the possibility of disturbing any asbestos in the course of
installation seek specialist guidance and use appropriate
equipment.
•Metal Parts: Take care when installing or servicing the
stove to avoid personal injury.
A faulty installation can cause danger to the inhabitants and
structure of the building.
For users of this appliance:
Your building insurance company may require you to inform them
that you have installed a new heating appliance. Check that your
cover is still valid after installing the appliance.
1. INSTALLING THE APPLIANCE
Each installation is unique to the property so it is not possible
to give details to suit every setting. The installation must comply
with Building Regulations and be made using "best practice"
construction methods.
Many fireplace openings have a supporting lintel. Do not remove
without supporting the remaining structure of the building. Do not
support the structure with the appliance or the flue system.
1.1 Take care when installing the appliance. Careless
handling and use of tools can damage the finish and/or
area.
1.2 To make the fitting of the Riva MF easier, gain better access
to the flue connection and protect paintwork from damage,
remove the internal components and the lower frame
fitting screws. The ashpit door, door and the front trim may
be removed on Riva products.
INSTALLATION INSTRUCTIONS
1.3 •Slide the Riva MF into the opening
•(Riva Only) If the Riva MF is to be fiited with a 4 sided
frame, fit the frame before fixing the appliance in to
position.
•(Riva Only) Check the fit of all frame options before fixing
the appliance into position
Some installations may require the frame to be fitted
before final fixing.
•Fixinplaceusingthefixingholeslocatedunderthe
ashpan, see diagram
•Fix using the kit provided
Tools required 10mm A/F spanner /socket wrench and
masonry drill)
PR7245
Securing Bolt Holes
1
•Ensure that the flange of the Riva MF is still flat against
the opening after tightening the fixing screws
1.4 Fill any void at the back or sides of the box with 6:1
vermiculite / cement mix or any other good quality non-
combustible insulation material. It is important that the
back and sides of the box are well insulated.
1.5 •Connect the flue liner and flue adaptor to the Riva MF by
inserting the flue spigot from the inside of the Riva MF
•Slide the flue pipe or liner adaptor inside the spigot
•Seal the flue to the spigot using fire cement
•Seal the spigot to the inside of the Riva MF using fire
cement. See diagrams 2, 3, 4.
In The U.k:
* England and Wales – Document J / Scotland - Part F/
Document J (Republic of Ireland only)
** In the U.K BS 8303, BS 6461, BS 7566
† registered body: HETAS (GB only)/INFO (Eire)
‡ Health and Safety at Work Act 1974