Filter
Top Products
5
[ (4.88) ( door height) (area/2) (minutes open) ( temp. di. ºF.)
(enthalpy incoming air – enthaply warehouse air) ] [ (1–X)]
Specic Volume of Incoming Air
Where X = % of heat transmission blocked by thermal barrier.
For freezers it becomes necessary to provide heat in the base slab
to avoid freezing of the ground water and heaving of the oor.
Minimum slab temperature should be at least 40ºF. Normally, 55ºF.
should be used for freezer applications.
2. Air Change Load
(a) Average Air Change- when the door to a refrigerated room is
opened, warm outside air will enter the room. This air must be
cooled to the refrigerated room temperature, resulting in an
appreciable source of heat gain. This load is sometimes called
the inltration load. The probable number of air changes per
day and the heat that must be removed from each cubic foot
of the inltrated air, are given in tables based on experience
(see Table 4, 5 & 6, page 14). For heavy usage, the inltration
may be doubled or more.
(b) Inltration Through a Fixed Opening- As an alternate to the
average air change method using the Psychrometric Chart
(page 37), the following formulas may be used to calculate
the inltration resulting from natural ventilation (no wind)
through external door openings.
The air change load can be substantial and every means
should be taken to reduce the amount of inltration entering
the box. Some eective means of minimizing this load are:
• Automatic closing refrigerator doors
• Vestibules or refrigerated anterooms
• Plastic strip curtains
• Air Curtains
• Inated bumpers on outside loading doors.
3. Miscellaneous Loads
Although most of the heat load in a refrigerated room
or freezer is caused by wall heat leakage, air changes and
product cooling or freezing, there are three other heat
sources that should not be overlooked prior to the selection
of the refrigeration equipment. Since the equipment has to
maintain temperature under design conditions, these loads are
generally averaged to a 24 hour period to provide for capacity
during these times.
(a) Lights- typically storage requirements are 1 to 1-1/2 watt per
square foot. Cutting or processing rooms can be double the
wattage. Each watt is multiplied by 3.42 BTU/watt to obtain a
BTUH gure. This is then multiplied by 24 to obtain a
daily gure.
(b) Motors- smaller motors are usually less ecient and tend to
generate more heat per horsepower as compared to larger
motors. For this reason Table 11, on page 18, is broken down
in to H.P. groups. Also, motors inside the refrigerated area will
reject all of their heat losses as shown in Table 11. However,
motors that are located outside but do the work inside, like
a conveyor, will reject less heat into the refrigerated space. If
powered material handling equipment is used, such as forklift
trucks, this must be included under Motor Heat Loads.
Generally only battery operated lift trucks are used in
refrigerated rooms, which represent a heat gain of 8,000 to
15,000 BTU/hr. or more over the period of operation. If motor
or loading conditions are not known, then calculate one
motor horsepower for each 16,000 cubic foot box in a storage
cooler and one HP for each 12,500 C.F. in a storage freezer
which allows for fan motors and some forklift operations.
These gures can be higher in a heavily used area, i.e. loading
dock or distribution warehouse.
(c) Occupancy- People working in the refrigerated storage area
dissipate heat at a rate depending on the room temperature
(Table 12, page 18). Multiple occupancies for short periods
should be averaged over a 24 hour period. If occupancy load
is not known, allow one person per 24 hour for each 25,000
cubic foot space.
4. Product Load
Whenever a product having a higher temperature is placed
in a refrigerator or freezer room, the product will lose its
heat until it reaches the storage temperature. This heat load
consists of three separate components: (see Table 7, page 15-
16).
(a) Specic Heat- The amount of heat that must be removed
from one pound of product to reduce the temperature of this
pound by 1ºF., is called its specic heat. It has two values: one
applies when the product is above freezing; the second is
applicable after the product has reached its freezing point.
(b) Latent Heat- The amount of heat that must be removed from
one pound of product to freeze this pound is called the latent
heat of fusion.
Most products have a freezing point in the range of 26ºF. to
31ºF. If the exact temperature is unknown, it may be
assumed to be 28ºF.
There is a denite relationship between the latent heat of
fusion and the water content of the product and its specic
and latent heats.
Estimating specic and latent heats:
Sp. Ht. above freezing = 0.20 + (0.008 X % water)
Sp. Ht. below freezing = 0.20 + (0.008 X % water)
Latent Heat = 143.3 X % water
(c) Respiration- Fresh fruits and vegetables are alive. Even in
refrigerated storage they generate heat which is called the
heat of respiration. They continually undergo a change in
which energy is released in the form of heat, which varies with
the type and temperature of the product. Tabulated values are
usually in BTU/lb./24 hours (Table 8, page 17), and are applied
to the total weight of product being stored and not just the
daily turnover.
(d) Pull down Time- When a product load is to be calculated at
other than a 24 hour pull down, a correction factor must be
multiplied to the product load.
24 hours
Pull down Time
Note: While product pull down can be calculated, no
guarantee should be made regarding nal product
temperature due to many uncontrollable factors (i.e., type of
packaging, position in the box, method of stacking, etc.)
5. Safety Factor
When all four of the main sources of heat are calculated,
a safety factor of 10% is normally added to the total
refrigeration load to allow for minor omissions and
inaccuracies (additional safety or reserve may be available
from the compressor running time and average loading).