Filter
Top Products
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
Page 2 of 8 F-8018 – FastRack Warewashing Systems
FastRack
WAREWASHING SYSTEMS
SPECIFICATIONS:
■ DESIGN: Fully automatic rack transport warewashing
system utilizing any Hobart C-Line-A dishwasher or
combination thereof. Design incorporates tables and
rack transport system providing continuous closed-
circuit operation.
■ OPERATION: Direction of operation may be specified
either clockwise or counterclockwise determined by
facing doors on C-Line machine. Inspection doors on
dishmachine may be specified to face either in or out.
■ CONSTRUCTION: As Applicable:
Dishwasher: Any Hobart C-Line-A Dishwasher or
combination thereof, selected according to production
requirements. Use portion of separate specifications for
C-Line-A model(s) selected. FastRack dishwasher is
standard with stainless steel front panel, frame, legs &
feet.
Tables: Table surface is #14 gauge stainless steel with
structural cross supports. Table sections are designed
with positive alignment and sealing bolted table joint
connections. All “H” frames and other supporting
members of 1
5
⁄8" diameter stainless steel tubing with
stainless steel adjustable feet. Inside width of tabling –
22
1
⁄4". Radius to outside of curved sections – 36".
Loading section of table incorporates a 1
1
⁄4" high rack
rest. Rack is disengaged from transport chain when
placed on lip, permitting stationary loading.
■ PREWASH
Straightaway Unit: RS-22A or PW-36A prewash unit in
straightaway to be specified as part of companion
C-Line-A dishwasher. Refer to individual machine
specifications.
On Curve: RS type prewash unit mounted in 90° or
120° hooded curved section of soiled dish table.
(PW-36A prewash available in straightaway only.)
Recirculating prewash with a stainless steel spray arm
above with special jets designed to effectively prewash
all type of tableware. Spray arm easily removed without
use of tools. Integral pump, motor and drain control
mounted externally on end of tank below table level.
Large, removable, perforated stainless steel strainer
screens sloped downward towards a deep perforated
stainless steel scrap basket. Basket and screens
removable at front of prewash. The scrap basket can be
removed and emptied without shutting machine down.
Prewash tank filled and replenished with overflow water
from companion machine. No fill valve required.
■ MOTORS: Refer to individual Hobart C-Line model
specifications.
■ CONTROLS: A stainless steel control center with power
“on/off” and “start/stop” switches is mounted on top of
machine. Machine control circuitry components will be
operated from a 120 volt control circuit transformer.
Electrical components are completely wired with 105°C,
600V thermoplastic insulated wire with stranded
conductors routed through Listed electrical conduit or
covered wireway built into the front of the machine
above tank water level. Extra push button station(s)
may be specified for other locations at extra cost.
■ FRC MODEL RACK TRANSPORT SYSTEM: Racks
are delivered through dishwashing machine by means
of 8,500 lb. tensile strength stainless steel endless
chain with oval driving lugs and stainless steel rollers.
The drive system transports racks without permanent
attachment, permitting instant engagement and disen
-
gagement of racks for cleaning, loading, substitution of
different racks, etc.
■ TRANSPORT CHAIN DRIVE:
1
⁄2 H.P. ball bearing motor
drives a speed reducer. Supplied in same electrical
specs as dishwasher. Speed reducer power train is
lubricated and cooled by an oil bath. A friction drive
clutch installed in low speed shaft of speed reducer and
directly connected to the drive sprocket shaft. Motor
has built-in overload protection with manual reset.
■ DRAIN CONNECTION: Single 2" female connection for
dishmachine. May be specified at either clean or soiled
dish end. Separate female drain connection for
disposer(s) and waste system.
■ BUILDING HOT WATER CONNECTION: Single 1" pipe
female connection. (It is recommended that the building
water temperature be 140°F.)
■ STEAM CONNECTION: If steam booster is specified,
single 1
1
⁄2" female connection for steam injector(s) or
steam coil(s) and steam booster.
■ ELECTRICAL CONNECTION: Single electrical
connection for all motors and operating controls.
Separate electrical connections required for electric
tank heat, electric booster, electric blower dryer,
disposer and waste system in front trough.
■ RACKS: Racks are not furnished as standard equip-
ment. A study of customer requirements must be made
to determine the number and type of racks required.
Hobart racks are recommended, however, most plastic
racks available from various rack suppliers with Hobart
indexing could be used on the FRC system. For further
information, see Warewashing Rack specification sheet
Form F-7861.
■ FILL: Fill water line is equipped with vacuum breaker
on downstream side of electrically operated solenoid
valve in common piping system, for automatic mainte
-
nance of tank level. Fill is interrupted whenever a door
is opened.
■ OPTIONAL EQUIPMENT AT EXTRA COST:
WASH TANK HEATING
ELECTRIC: Electric incoloy sheathed immersion
heaters removable from inside tank. Tank water
temperature is controlled by solid-state thermostat with
positive low-water protection and magnetic contactor.
(Disconnect switches not furnished.) Heating elements