Filter
Top Products
6
GB
Installation
Moving the Cooker
Fig. B
Fig. C
Gas connection
The cooker should be connected to the gas-supply
by a corgi registered installer. During installation of
this product it is essential to fit an approved gas tap
to isolate the supply from the appliance for the
convenience of any subsequent removal or
servicing. Connection of the appliance to the gas
mains or liquid gas must be carried out according to
the prescribed regulation in force, and only after it is
ascertained that it is adaptable to the type of gas to
be used. If not, follow the instructions indicated in
the paragraph headed “Adaptation to different gas
types”. On some models the gas supply can be
connected on the left or on the right, as necessary;
to change the connection, reverse the position of the
hose holder with that of the cap and replace the
gasket (supplied with the appliance). In the case of
connection to liquid
gas, by tank, use
pressure regulators
that conform to the
regulation in force.
The gas supply must
be connected to the
left of the appliance.
Be sure that the
hose does not pass
through the rear of
the cooker touching hot parts.
!!
!!
! Make sure the supply pressure conforms with the
values shown in the table entitled “Caracteristics of
the burners and nozzles”.
When the cooker is installed betweenWhen the cooker is installed between
When the cooker is installed betweenWhen the cooker is installed between
When the cooker is installed between
cabinets (recessed), the gas connectioncabinets (recessed), the gas connection
cabinets (recessed), the gas connectioncabinets (recessed), the gas connection
cabinets (recessed), the gas connection
must be effected by an approved flexiblemust be effected by an approved flexible
must be effected by an approved flexiblemust be effected by an approved flexible
must be effected by an approved flexible
hose with bayonet fittinghose with bayonet fitting
hose with bayonet fittinghose with bayonet fitting
hose with bayonet fitting
(BS 669 Current Edition). The gas inlet for(BS 669 Current Edition). The gas inlet for
(BS 669 Current Edition). The gas inlet for(BS 669 Current Edition). The gas inlet for
(BS 669 Current Edition). The gas inlet for
the cookers is a threaded G 1/2 gas femalethe cookers is a threaded G 1/2 gas female
the cookers is a threaded G 1/2 gas femalethe cookers is a threaded G 1/2 gas female
the cookers is a threaded G 1/2 gas female
fitting.fitting.
fitting.fitting.
fitting.
HOT PARTS
600 mm
Connecting the gas supply
To make the connection, a flexible hose should be
used corresponding to the current gas regulations
which are:
• the hose must never be at any point in its lenght
in contact with the “hot” parts of the cooker;
• the hose must never be longer than 1,5 metre;
• the hose must not be subject to any tension or
torsional stress and it must not have any
excessively narrow curves or bottlenecks;
• the hose must be easy to inspect along its entire
length to check its condition;
• the hose must always be in good condition, never
attempt to repair.
!!
!!
! The installation must comply with gas safety
(installation and use) regulations 1984. In all cases
for the above, by low, a qualified, corgi approved
engineer must be called for installation.
Disposing of the appliance
When disposing of the appliance please remove the
plug by cutting the mains cable as close as
possible to the plug body and dispose of it as
described above.
Adapting the cooker to different types of gas
In order to adapt the cooker to a different type of
gas with respect to the gas for which it was
produced (indicated on the label attached to the lid),
follow these steps:
a)a)
a)a)
a)replace the hose holder mounted on the
appliance with that supplied in the bag of
“cooker accessories”.
b)b)
b)b)
b)Replacing the burner nozzles on the hob:
• remove the grids and slide the burners from their
housings;
• unscrew the nozzles using a 7 mm socket
spanner, and replace them with nozzles for the
new type of gas (see
table 1 “Burner and
nozzle characteristics”).
• replace all the
components by
repeating the steps in
reverse order.