Hotpoint SX 1038N CX Convection Oven User Manual


 
GB
5
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
! The first time you use your appliance, heat the
empty oven with its door closed at its maximum
temperature for at least half an hour. Make sure that
the room is well ventilated before switching the oven
off and opening the oven door. The appliance may
emit a slightly unpleasant odour caused by
protective substances used during the manufacturing
process burning away.
! To make the setting process easier, press and
hold the + and
– buttons to scroll through the
numbers on the display rapidly.
! Each setting will automatically be stored in the
appliance memory after 10 seconds.
! The touch controls cannot be activated if the user
is wearing gloves.
Some models are equipped with a system of hinges
which allows the door to close slowly, without the
user having to follow the movement through with his/
her hand. To use the system correctly, before
closing the door:
Open the door fully.
Do not force the closing movement manually.
Control panel lock
! The control panel can be locked while the oven is
off, once cooking has started or finished and during
programming.
To lock the oven controls, press and hold the
button for at least 2 seconds. A buzzer will sound
and the TEMPERATURE display shows the key
symbol “O—n”. The icon will light up to indicate
lock activation.
To deactivate the lock, press and hold the
button again for at least 2 seconds.
Setting the clock
! The clock can only be set when the oven is
switched off. If the oven is in standby mode,
pressing the
button once will display the current
time setting. Press it again to set the time.
After connection to the power supply network or after
a blackout, the
button and the digits on the
TIME display will flash for 10 seconds.
To set the clock:
1. Press the
button.
2. Adjust the hour figure using the + and - buttons.
3. Once you have reached the correct hour value,
press the
button.
4. Repeat the above process to set the minutes.
If a blackout occurs, it will be necessary to reset the
clock. If the
icon flashes on the display, this
indicates that the clock has not been set correctly.
Setting the minute minder
! The minute minder may be set regardless of
whether the oven is switched on or off. It does not
switch the oven on or off.
When the set time has elapsed, the timer emits a
buzzer that will automatically stop after 30 seconds
or when any active button on the control panel is
pressed.
To adjust the timer proceed as follows:
1. Press button
.
2. Set the desired time using buttons
+ and -.
3. Once you have reached the desired value, press
the
button again.
The lit
symbol will remind you that the minute
minder is on.
To cancel the minute minder, press the
button
and use the + and – buttons to set the time to 00:00.
Press button
again.
The
icon will switch off to indicate that the minute
minder has been disabled.
Starting the oven
1. Switch the control panel on by pressing the
button. The appliance buzzer sounds three times
(ascending) and all buttons light up in sequence.
2. Press the button corresponding to the desired
cooking mode. The TEMPERATURE display shows:
- the temperature associated with the mode, if
programming manually;
- “Auto”, if programming is automatic.
The TIME display shows:
- the current time, if programming manually;
- the duration, if programming is automatic.
3. Press the
button to begin cooking.
4. The oven will begin its preheating phase, the
preheating indicators will light up as the temperature
rises.
5. When the preheating process has finished, a
buzzer sounds and all the preheating indicator lights
show that this stage has been completed: the food
can then be placed in the oven.
6. During cooking it is always possible to:
- change the temperature by pressing the
button, followed by the + and - buttons (
manual
modes only
);
Start-up and use