Jenn-Air JES9860 Range User Manual


 
12
4. Select AUTO or MANUAL.
AUTO will automatically prompt you to enter a Bake
temperature on Friday at 2 p.m. and stay in Sabbath mode for
33 hours. “SABBATH” and “SABBATH ENABLE” appear in
the display for 90 minutes. If Bake or Cook/Hold Bake are
desired during Sabbath Mode, they must be programmed
during this 90-minute period before AUTO Sabbath Mode is
active.
MANUAL sets the oven to Sabbath Mode for 72 hours.
“SABBATH” and “SABBATH ENABLE” appear in the display
for 5 minutes. If Bake or Cook/Hold Bake are desired during
Sabbath Mode, they must be programmed during this
5-minute period before the MANUAL Sabbath Mode is active.
5. Select ON or OFF.
To cancel Sabbath mode:
1. Press CANCEL.
2. Press and hold SETUP for 5 seconds.
Temp Adjust
Oven temperatures are tested at the factory. It is normal to notice
some baking time or browning differences between a new oven
and an old one. As ovens get older, the oven temperature can
shift.
You may adjust the oven temperature if you think the oven is not
baking or browning correctly. To decide how much to change the
temperature, set the oven temperature 25°F higher or lower than
the temperature in your recipes, then bake. The results of the first
bake should give you an idea of how much to adjust the
temperature.
To adjust the oven temperature:
1. Press SETUP.
2. Use right Quickset pad to scroll to TEMP ADJUST.
3. Select TEMP ADJUST using the left Quickset pad.
4. Enter the desired temperature change using the number
pads.
5. Use the Quickset pads to select “+/-” to indicate an increase
or decrease in temperature. The temperature change is
displayed at the top of the window.
6. Press ENTER or wait 3 seconds to accept the change.
7. Press SETUP to exit the menu.
The oven temperature does not need to be readjusted if there is a
power failure or interruption.
Broiling and cleaning temperatures cannot be adjusted.
208/240V
For improved results when using Bake, the oven can be set from
240V to 208V if your household is on 208V.
To set the oven to 208V:
1. Press SETUP.
2. Use right Quickset pad to scroll to 208/240V.
3. Select 208/240V using the left Quickset pad.
4. Select 208V or 240V using the Quickset pads.
5. Press SETUP to exit the menu.
Tones (beeps)
The number of beeps heard at the end of cooking and at the end
of timer operation and their volume can be adjusted.
To change the beeps at the end of cooking:
1. Press SETUP.
2. Use right Quickset pad to scroll to TONES.
3. Select TONES using the left Quickset pad.
4. Use right Quickset pad to scroll to COOK TONE.
5. Select COOK TONE using the left Quickset pad.
6. Use the right Quickset pad to scroll and select:
1-30 SEC to hear 1 beep every 30 seconds.
OR
1-60 SEC to hear 1 beep every 60 seconds.
OR
1 BEEP to hear 1 beep only at the end of cooking.
7. Select the desired beep using the left Quickset pad.
8. Press SETUP to exit.
To change the timer beeps:
1. Press SETUP.
2. Use right Quickset pad to scroll to TONES.
3. Select TONES using the left Quickset pad.
4. Use right Quickset pad to scroll to TIMERS TONES.
5. Select TIMERS TONES using the left Quickset pad.
6. Use the right Quickset pad to scroll and select:
1-30 SEC to hear 1 beep every 30 seconds.
OR
1-60 SEC to hear 1 beep every 60 seconds.
OR
1 BEEP to hear 1 beep only at the end of cooking.
7. Select the desired beep using the left Quickset pad.
8. Press SETUP to exit.
To change the volume of the beeps:
1. Press SETUP.
2. Use right Quickset pad to scroll to TONES.
3. Select TONES using the left Quickset pad.
4. Use right Quickset pad to scroll to VOLUME.
5. Select VOLUME using the left Quickset pad.
6. Use right Quickset pad to scroll and select:
HIGH for the highest volume.
OR
MEDIUM for medium volume.
OR
LOW for the lowest volume.
7. Select the desired volume using the left Quickset pad.
8. Press SETUP to exit.
12 HR Shutoff
The oven will automatically turn off at the end of 12 hours if you
unintentionally leave it on.
To turn off this feature:
1. Press SETUP.
2. Use right Quickset pad to scroll to 12HR SHUTOFF.
3. Select 12HR SHUTOFF using the left Quickset pad.
4. Select ON or OFF using the Quickset pads.
5. Press SETUP to exit.