Filter
Top Products
22
Prepare Cooktop:
■ Remove plastic items from the cooktop because they may
melt.
NOTE: Oven temperature must be below 400°F (205°C) to
program a clean cycle.
How the Cycle Works
IMPORTANT: The heating and cooling of porcelain on steel in the
oven may result in discoloring, loss of gloss, hairline cracks and
popping sounds.
The Self-Cleaning cycle uses very high temperatures, burning soil
to a powdery ash.
Suggested clean times are 2 hours for light soil and between
3 hours and 4 hours for average to heavy soil.
Once the oven has completely cooled, remove ash with a damp
cloth. Do not wipe down any of the inside surfaces until the oven
has completely cooled down. To avoid breaking the glass, do not
apply a cool damp cloth to the inner door glass before it has
completely cooled.
The oven light will not work during the Self-Cleaning cycle.
When “LOCKED” shows in the display, the door cannot be
opened. To avoid damage to the door, do not force the door open
when “LOCKED” is displayed.
To Self-Clean:
Before self-cleaning, make sure the door is closed completely. If
the oven door is left open, “CLOSE DOOR” will appear in the
display until the door is closed.
1. Press CLEAN.
2. “REMOVE RACKS” will be displayed. Remove the racks.
3. Select CONTINUE using the Quickset pad. The Quickset
pads are located on either side of the control panel display.
4. Set LIGHT soil level by entering “200” using the number pads
for 2 hours of cleaning time.
OR
Select MEDIUM for a moderately soiled oven and 3 hours of
cleaning time.
OR
Select HEAVY for a heavily soiled oven and 4 hours of
cleaning time.
“CLEAN,” “TIME,” “LOCKED” and the cleaning time
countdown will be displayed while the oven is cleaning.
“OVEN COOLING” will appear in the display when the
cleaning time has been completed and the oven is still
locked.
The door lock will disengage approximately 1 hour after the
cleaning time is completed. OVEN COOLING will go off in the
display when the oven door has unlocked.
To Delay Start Self-Clean:
1. Press CLEAN.
2. “REMOVE RACKS” will be displayed. Remove the racks.
3. Select CONTINUE using the Quickset pad.
4. Set LIGHT soil level by entering “200” using the number pads
for 2 hours of cleaning time.
OR
Select MEDIUM for a moderately soiled oven and 3 hours of
cleaning time.
OR
Select HEAVY for a heavily soiled oven and 4 hours of
cleaning time.
The door will lock. “CLEAN,” “TIME,” “LOCKED” and the
cleaning time countdown will be displayed
5. After door locks, press MORE OPTIONS.
6. Select DELAY using the Quickset pad.
7. Select the number of hours you want to delay the start of the
self-clean cycle.
The delay time and cleaning time will be displayed.
General Cleaning
IMPORTANT: Before cleaning, make sure all controls are off and
the oven and cooktop are cool. Always follow label instructions
on cleaning products.
Soap, water and a soft cloth or sponge are suggested first unless
otherwise noted.
EXTERIOR PORCELAIN ENAMEL SURFACES
(on some models)
Food spills containing acids, such as vinegar and tomato, should
be cleaned as soon as the entire range is cool. These spills may
affect the finish.
Cleaning Method:
■ Glass cleaner, mild liquid cleaner or nonabrasive scrubbing
pad:
Gently clean around the model and serial number plate
because scrubbing may remove numbers.
■ All-Purpose Appliance Cleaner Part Number 31682 (not
included):
See “Assistance or Service” section to order.
STAINLESS STEEL (on some models)
To avoid damage to stainless steel surfaces, do not use soap-
filled scouring pads, abrasive cleaners, Cooktop Cleaner, steel-
wool pads, gritty washcloths or abrasive paper towels.
Cleaning Method:
Rub in direction of grain to avoid damaging.
■ Stainless Steel Cleaner and Polish Part Number 31462 (not
included):
See “Assistance or Service” section to order.
■ Liquid detergent or all-purpose cleaner:
Rinse with clean water and dry with soft, lint-free cloth.
COOKTOP CONTROLS
To avoid damage to the cooktop controls, do not use steel wool,
abrasive cleansers or oven cleaner.
To avoid damage, do not soak knobs.
When replacing knobs, make sure knobs are in the Off position.
Do not remove seals under knobs.
Cleaning Method:
■ Warm, soapy water:
Pull knobs straight away from control panel to remove.