Filter
Top Products
10
15.5 Programming portion of hot water
Ⅲ Place a cup under the pivoting nozzle (18).
Ⅲ : HOT WATER PORTION / PRESS FOR HOT
WATER
Ⅲ : ENOUGH HOT WATER ? / PRESS FOR HOT
WATER
Ⅲ : HOT WATER PORTION / PRESS FOR HOT
WATER
Ⅲ Press the key in order to reach the next phase or the key
EXIT to quit the programming.
15.6 Programming water hardness
Ⅲ : WATER HARDNESS
LEVEL 3
Ⅲ Press the key PROG.
Ⅲ You can set the water hardness by pressing the keys or .
Ⅲ To store, press the key PROG.
Ⅲ Press the key in order to reach the next phase or the key
EXIT to quit the programming.
To determine the water hardness, please read Chapter 8
“Setting the water hardness”
15.7 Programming CLOCK
Programming the clock is necessary if the function “Machine on”
is used.
Ⅲ : TIME.
—:—
Ⅲ Press the key PROG.
Ⅲ By pressing the keys or you can set the hours.
Ⅲ To store, press the key PROG.
Ⅲ By pressing the keys or you can set the minutes.
Ⅲ To store, press the key PROG.
Ⅲ Press the key in order to reach the next phase or the key
EXIT to quit the programming.
15.8 Programming machine on
Programming the clock is necessary if the function “Machine on”
is used.
Ⅲ : UNIT
ON —:—
Ⅲ Press the key PROG.
Ⅲ By pressing the keys or you can set the hours.
Ⅲ To store, press the key PROG.
Ⅲ By pressing the keys or you can set the minutes.
Ⅲ To store, press the key PROG.
Ⅲ Press the key in order to reach the next phase or the key
EXIT to quit the programming.
The display —:— means that the function is switched off
15.9 Programming machine off
Ⅲ : UNIT OFF
5.0 HRS.
Ⅲ Press the key PROG.
Ⅲ By pressing the keys or you can set the hours (switched
off or 0.5 hrs. – 9 hrs.).
Ⅲ To store, press the key PROG.
Ⅲ Press the key in order to reach the next phase or the key
EXIT to quit the programming.
+
-
+
+
-
+
-
+
+
-
+
-
+
+
-
+
+
15.10 Draw-offs
Ⅲ : AUDIT TRAIL (total audit trail)
Ⅲ Press the required draw-off key to inquire the draw-offs.
Ⅲ Press the key in order to reach the next phase or the key
EXIT to quit the programming.
Draw-offs of steam cannot be inquired.
15.11 Programming language
Ⅲ Press the key PROG.
Ⅲ By pressing the keys or you can select the required
language.
Ⅲ To store, press the key PROG.
Ⅲ Press the key in order to reach the next phase or the key
EXIT to quit the programming.
16. Care and maintenance
16.1 Fill water
Ⅲ : FILL WATER TANK
Ⅲ When this display lights up, no more drawing-off is possible. Fill
with water as described under Section 3.3.
The water tank should be rinsed out every day and filled
with fresh water.
If you use an automatic filling device, we recommend that
you rinse the water tank out regularly and fill it up with fresh
water.
16.2 Installation of an automatic filling device
Please read the operating instructions of the automatic filling
device.
16.3 Empty grounds container
The grounds container collects the coffee grounds.
Ⅲ : EMPTY DRAWER
Ⅲ When this display lights up, no more draw-offs are possible and
the grounds container must be emptied.
Ⅲ Carefully remove the drip tray – there is water in it. Then re-
move the grounds container (Fig. 4).
16.4 Empty drip tray
Ⅲ : EMPTY DRIP TRAY
Ⅲ When this display lights up, no more draw-offs are possible and
the drip tray must be emptied.
Ⅲ Carefully remove the drip tray – there is water in it (Fig. 4).
16.5 Grounds container missing
Ⅲ : DRAWER MISSING
Ⅲ When this display lights up, the grounds container has not been
inserted properly or is missing.
16.6 Drip tray missing
Ⅲ : DRIP TRAY MISSING
Ⅲ When this display lights up, the drip tray has not been inserted
properly.
+
-
+
+