Filter
Top Products
The appliance should be connected
directlv to the fused disconnect or
circuit breaker dox through flexible, armored or
non-metallic sheathed, copper cable (with
grounding wire). Locate the junction box to allow
two to three feet of slack in the line so that the
range can be moved if servicing is ever
necessary. Do Not cut the conduit.
A U.L.-listed conduit connector
must
be
provided at each end of the power supply cable
(at the appliance and at the junction box). Wire
sizes (COPPER WIRE ONLY) and connections
must conform with the rating of the appliance.
El
The Tech Sheet is in a pouch
attached to the left hand underside of
the oven. To access, remove the storage
drawer (slide-in) or grille (drop-in).
Electrical
connection
Electrical Shock Hazard
l
Electrical ground is required on this
appliance.
l
Do Not connect to the electrical
supply until appliance is permanently
grounded.
l
Disconnect power to the junction box
before making the electrical
connection.
l
This appliance must be connected to
a grounded, metallic, permanent
wiring system, or a grounding
connector should be connected to
the grounding terminal or wire lead
on the appliance.
Failure to do so could result in a fire,
personal injury or electrical shock.
This appliance is manufactured with the
white (neutral) power supply wire and a
cabinet-connected green grounding wire
twisted together.
Connect the appliance cable to the junction
box through the U.L.-listed conduit
connector. Complete electrical connection
according to local codes and ordinances.
A. Where local codes permit...
connecting the cabinet-grounding conductor
to the neutral (white) junction box wire:
Cable from
Junction
power supply
I
Bare 0Ym
green wire
Figure 1
Cable from
range
conduit
connector
Grounded Neutral
1. Disconnect the power supply.
2. Connect together 3 wires: green and white
appliance cable wires and the neutral (white)
wire in junction box.
3. Connect the two black wires together; then
the two red wires together. See Figure 1.
B. Where local codes Do Not
permit...
connecting the cabinet-grounding conductor
to the neutral (white) junction box wire:
Cable from
green
wires
kFZJ L-listed
Cable from c&fuit
range
connector
Figure 2
Ungrounded Neutral
1. Disconnect the power supply.
2. Separate the green and white appliance
cable wires.
3. Connect the white appliance cable wire to the
neutral (white) wire in the junction box.
4. Connect the two black wires together; then
the two red wires together. See Figure 2.
5. Connect the green grounding wire to a
grounded wire in the junction box.
C. If connecting to a four-wire
electrical system:
DO NOT connect the cabinet-grounding
conductor to the neutral (white) junction box
wire.
Cable from conduit
Figure 3
range connector
1. Disconnect the power supply.
2. Separate the green and white appliance cable
wires.
3. Connect the white appliance cable wire to the
neutral (white) wire in the junction box.
4. Connect the two black wires together; then
the two red wires together. See Figure 3.
5. Connect the green grounding wire to the
grounding wire in the junction box.
Tm Now start...
With range in kitchen.
II
n
Remove shipping materials, tape, and
protective film from range.
Do Not
remove shipping base at this time.
12
Remove the racks and other parts
. from inside the oven.
Insert a nail or a 5/32” diameter item in the hole
in each of the hinges. Close the door as far as
possible. Lift oven door off of the hinges and set
aside.
1
I
I
Slide-in installation:
Remove storage drawer.
Drop-in installation:
Remove storage drawer
and the side bottom panels. Install Kit. No.
3183638 (black), 3183639 (white), or 3183640
(almond) according to the Installation
Instructions packed with kit.
I
Floor Damage
Before moving range across floor, check
that range is on shipping base or slide
range onto cardboard or hardboard.
Failure to do so could cause damage to
floor covering.
15
.
Move range close to cabinet cutout.
Make electrical connection. See
“Electrical requirements” and “Electrical
connection” sections, Panels A and B, for details.
Personal Injury Hazard
Because of the weight and size of this
range, two or more people are needed to
move and safely install it.
Failure to do so could result in personal
injury.
Use this area to grip.
range. Lift range up to cabinet opening using
the oven opening as an area to grip.
.
I
I
Center range in cabinet cutout. Loosen screws
and insert spacers (shipped in literature bag) on
each side of the control console. If range does
not fit properly, check spacers. The spacers
Panel B