KitchenAid KERC506 Range User Manual


 
11
Displays
When power is first supplied to the appliance, everything on the
displays will light up for 5 seconds. Then, PF will appear. Press
CANCEL OFF to clear displays.
If PF appears at any other time, a power failure has occurred.
Press CANCEL OFF and reset the clock if needed.
Oven Display (on some models)
When the oven is in use, this display shows the oven temperature,
heat source(s) and start time.
During Timed Cooking, this display also shows a timed
countdown.
If Err appears on the display, an invalid pad was pressed.
Press CANCEL OFF and retry your entry.
When the oven is not in use, the display will show the time of day.
Time of Day/Timer Display (on some models)
This display shows the time of day or Timer countdown.
Start
The START pad begins any oven function except the Timer and
Control Lock. If not pressed within 5 seconds after pressing a
pad, START? will appear on the oven display as a reminder. If
not pressed within 5 minutes after pressing a pad, the oven
display will return to the clock and the programmed function will
be canceled.
Cancel Off
The CANCEL OFF pad stops any oven function except for the
Clock, Timer and Control Lock.
Clock
This is a 12-hour clock and does not show a.m. or p.m.
To Set:
1.
Press CLOCK SET/START.
2.
Press number pads to set time of day.
On some models, press the HR and MIN up or down
arrow pads (buttons) until the correct time shows on the
display.
3.
Press START.
To n e s
Tones are audible signals, indicating the following:
One tone
Valid pad press
Oven is preheated
Function has been entered
Three tones
Invalid pad press
Four tones
End of cycle
Reminder, repeating each minute after the end-of-cycle tones
To Remove Tones:
Press and hold STOP TIME. Repeat to turn back on.
Reminder Tones Only
The Minute Timer and Timed Cooking reminder tones are preset
on, but can be turned off.
To Turn Tones Off/On:
Press and hold TIMER SET/START until a
tone sounds. Repeat to turn back on.
End-of-Cycle and Reminder Tones
The Timer and Timed Cooking end-of-cycle and reminder tones
are preset on, but can be turned off. However, on double oven
models, if all tones have been turned off, the end-of-cycle and
reminder tones cannot be independently turned on.
To Turn Tones Off/On:
Press and hold COOK TIME until a tone
sounds and the oven display returns to the clock. Repeat to turn
back on.
Tone Volume
The volume is preset at high, but can be changed to low.
To Change:
Press and hold the DELAY START for five seconds. A
tone will sound, and Snd Lo will appear on the oven display for 3
seconds. Repeat to change back to Snd HI.
Fahrenheit and Celsius
To set oven to cook in Celsius instead of Fahrenheit, press and
hold BROIL for 5 seconds. Repeat to change back into
Fahrenheit.
Timer
The Timer can be set in minutes and seconds or hours and
minutes and counts down the set time.
NOTE:
The Timer does not start or stop the oven.
To Set:
1.
Press TIMER SET/START.
Press again to switch between MIN/SEC and HR/MIN.
If no action is taken after 1 minute, the display will return to the
time of day mode.
2.
Press the number pads to set length of time.
On some models, press the HR and MIN up or down
arrow pads (buttons) until the correct time shows on the
display.
3.
Press TIMER SET/START.
If not pressed within 5 seconds, the display will return to the
time of day mode and the programmed function will be
canceled.
When the set time ends, if on, end-of-cycle tones will sound,
then reminder tones will sound every minute.
4.
Press TIMER CANCEL anytime to cancel the Timer and/or
stop reminder tones.
Remember, if Cancel Off is pressed, the oven will turn off.
The time can be reset during the countdown by repeating the
above steps.
Control Lock
The Control Lock shuts down the control panel pads to prevent
unintended use of the oven. The Control Lock is preset unlocked,
but can be locked.
When the control is locked, only the TIMER SET/START and
TIMER CANCEL pads will function.
To Lock/Unlock Control:
Before locking, make sure the oven, the
Timer and Timed Cooking are off. Press and hold START for about
5 seconds until LOC and a picture of a lock appear on the
display. Repeat to unlock and remove CONTROL LOCK from
the display.