Filter
Top Products
Hi-Temp Scrub
Select this option to heat the water during parts of the cycle, and
add a rinse. Higher water temperatures and an extra rinse help
clean tough soils. Hi-Temp Scrub, with the Heavy Duty cycle,
heats the water in the main wash and the prewash.
Hi-Temp Scrub, with the Normal cycle, raises the water
temperature in the main wash.
This option adds heat, water, and wash time to a cycle.
NOTE: Hi-Temp Scrub is an option with the Heavy Duty and
Normal cycles.
Sani Rinse
Select this option to raise the water temperature in the final rinse
to approximately 155°F (68°C). The Sani Rinse option adds heat
and time to the cycle. This high temperature rinse sanitizes your
dishes and glassware in accordance with NSF/ANSI Standard 184
for Residential Dishwashers. Certified residential dishwashers are
not intended for licensed food establishments.
NOTE: The Heavy Duty cycle automatically uses this option. Sani
Rinse is an option with the Normal cycle. Only these sanitization
cycles have been designed to meet the NSF/ANSl requirements.
Heat Dry
The Heat Dry option in combination with rinse aid will give you
excellent drying results. The energy to use Heat Dry costs pennies
per cycle. Heat Dry is on when the light is lit on the Heat Dry
button. Be sure to load plastic items in the upper rack to avoid
damage.
You may turn off the Heat Dry option by pressing HEAT DRY so
that the light goes off. However, you will have items in your dish
load that will not be dry at the end of the cycle.
NOTE: The Heat Dry option is used in all cycles except Rinse
Only.
Control Lock
Use control lock to avoid unintended use of your dishwasher. You
can also use the control lock feature to avoid unintended cycle or
option changes during a cycle.
When Control Lock is lit, all buttons are disabled.
NOTES:
• The dishwasher door can be opened while the controls are
locked.
• You can turn on the lock while the dishwasher is running.
To turn on the lock
Press and hold HEAT DRY for at least 4 seconds. The Control
Lock light glows.
If you press any pad while your dishwasher is locked, the light
flashes 3 times.
To turn off the lock
Press and hold HEAT DRY for at least 4 seconds. The Control
Lock light turns off.
4 Hour Delay
Select this option to run your dishwasher at a later time or during
off-peak hours. You can add items to the load anytime during the
delay countdown. (See "Adding Items During a Cycle.") The delay
countdown will not continue if the door is not closed firmly.
To delay the start (Model KUDU03ST)
1. Open the door.
2. Select a wash cycle and options. The selected cycle and
option lights will glow.
3. Press 4 HOUR DELAY.
You will see
showing in the display. The 4 Hour Delay light will glow.
4. Press START/RESUME. The Start/Resume light will glow.
5. Close the door firmly.
NOTE: To cancel the delay, open the door and press 4 HOUR
DELAY. To immediately start your dishwasher, press START/
RESUME.
To delay the start (all other models)
1. Open the door.
2. Select a wash cycle and options. The selected cycle and
option lights will glow.
3. Press 4 HOUR DELAY.The 4 Hour Delay light will glow.
4. Press START/RESUME.
5. Close the door firmly within 3 seconds of pressing Start/
Resume.
NOTE: To cancel the delay, open the door and press 4 HOUR
DELAY. To immediately start your dishwasher, press START/
RESUME and close the door firmly within 3 seconds.
Sanitized
If you select the Sani Rinse option, Sanitized light glows when the
Sani Rinse cycle is finished. If your dishwasher did not properly
sanitize your dishes, the light flashes at the end of the cycle. This
can happen if the cycle is interrupted. The light goes off when you
open and close the door or press CANCEL.
Clean
The Clean light glows when a cycle is finished. The light turns off
when you open and close the door or press CANCEL.
15