Liebherr 7081 203-00 Refrigerator User Manual


 
7
Setting up
• Avoid positioning the appliance in direct sunlight or near cookers,
radiators and similar sources of heat.
• The floor on which the appliance stands should be horizontal and
level.Compensate for uneven floors with the adjustable feet.
• Always ensure that there is good ventilation and that the outward
flowing air is able to escape.
• Standard EN 378 specifies that the room in which you install your
appliance must have a volume of 1 m
3
per 8 g of R 600a refrigerant
used in the appliance, so as to avoid the formation of inflammable
gas/air mixtures in the room where the appliance is located in the
event of a leak in the refrigerant circuit. The quantity of refrigerant
used in your appliance is indicated on the type plate on the inside
of the appliance.
• Do not connect the appliance to the supply with other equipment
using an extension cable - risk of overheating.
• Always install the appliance directly against the wall.
Connecting to the mains
Power supply (a.c.) and voltage at the operating point must comply
with the details on the type plate. The socket must be fused with a
10 A fuse or higher, it must be away from the rear of the appliance
and must be easily accessible.
Connect the appliance with a properly earthed fused plug
and socket only.
GB
Climate rating
The appliance is set to operate within specic ambient temperature
limits according to its climate rating. These temperature limits should
not be exceeded. The correct climate rating for your appliance is
indicated on the type plate.
Climate rating Ambient temperature
SN +10°C to +32°C
N +16°C to +32°C
ST +16°C to +38°C
T +16°C to +43°C
The appliance complies with the relevant safety regulations and
EC directives 2004/108/EC and 2006/95/EC.
Dimensions
Operating and control elements
1
Temperature display
2
Temperature setting buttons
3
Audible warning on/off button
4
Fan on/off button
5
Child-proof lock
6
On/off button
Setting the temperature
To reduce the temperature: Press the DOWN button;
To increase the temperature: Press the UP button.
- While you are entering the temperature, the set temperature will
flash on the display.
- You can change the settings in increments of 1°C briefly pressing
the button again.
- The electronic controls will switch over automatically about 5
seconds after the last time you pressed the button, and the actual
temperature will be displayed.
If
F 1 appears in the display, the appliance has a fault. Consult your
nearest customer service point.
Fan switch
Thereby a climate which corresponds to that of a wine cellar is
achieved inside the wine cooler. Corks are prevented from drying
out due to an increased level of humidity.
To switch on: Press the Ventilation button. The indicator
lamp in the switch will light up.
To switch o: Press the Ventilation button. The indicator
lamp in the switch goes dark.
Switching the appliance on and o
You are recommended to clean the appliance before switch ing it
on for the rst time (see Cleaning). Connect the appliance to the
mains - the appliance is switched on.
• To switch the appliance on: Press the ON / OFF button until
the Display lights up.
• To switch the appliance off: Keep the ON / OFF button pressed
for 3 sec. so that the temperature display goes out.
Storing wine
If you are storing wine for long periods of time, it should be stored
at a temperature of between 10°C and 14°C.
This is the temperature wine cellars are kept at, and it is just right
to allow wine to mature properly.
The following drinking temperatures are recommended for the
various types of wine.
Red wines: +14°C to +18°C
Rosé wines: +10°C to +12°C
White wines: +8°C to +12°C
Sparkling wines, Prosecco +7°C to +9°C
Champagne +5°C to +7°C
Caution!
The maximum load capacity of the wood racks is 80 kg.