Filter
Top Products
MQ-MIKASA MVH-702DRSC COMPACTOR — PARTS & OPERATION MANUAL — REV. #1 (12/17/03) — PAGE 11
MVH-702DRSC — OPERATION AND SAFETY DECALS
Figure 1 displays the operation and safety decals as they appear on the compactor. Should any of these decals become damaged
or unreadable, contact the Multiquip Parts Department for a replacement set.
Figure 1b. Operation and Safety Decals
J
NPA-927
DIESEL
FUEL
ONLY
J
NPA-922
OPEN
OPERATIONAL CAUTION
1. Operating multiple machines on a jobsite
Each machine has a remote control channel setting, both in the plate and in the transmitter. To assure proper operation the channel numbers must match
between the machine and the transmitter. When using more than one machine at the same jobsite, each machine and accompanying transmitter must be
set a t a different channel number than the other machines but each machine should still match its transmitter.
2. Air Filter service
a. If air cleaner element is clogged, the over-heat lamp will come on.
b. Clean up or replace the cleaner element immediately. Otherwise, machine vibration will stop automatically and will not start its vibration again until the engine
has enough time to cool down.
SIGNAL
CHANNEL
BATTERY
CHARGE
INLET
MVH-906
OFF
ON
MAIN SWITCH
EMERGENCY STOP
BATTERYSIGNAL CHARGE
START STOP
OFF
ON
ENGINE
SWITCH
VIBRATION
SWITCH
CAUTION
1. Read owner’s instruction manual before operating or servicing this machine.
2. The machine consists of the engine located in front, and the aluminum hydraulic oil tank in
5.
rear. The operator should stand 7 feet (2m) away from to operate the machine. When
operating the plate while standing in front of the machine please note that the travel controls
will function in the opposite direction.
3. The remote control operation is restricted to a narrower area the further you are from the
machine. The transmitter should be pointed more directly toward the machine.
4. In case for emergency such as the failure of the transmitter, pull Emergency Stop Lever
located on the machine immediately and wait until the engine stops completely.
The remote control operation is not available in the following cases and the vibration stops
automatically in operation.
The case A: Operator stands within approx. 3 feet (1m) distance, to operate machine.
The case B: Operator stands approx. 60 feet (10m) or father from the machine, to operate
[approx. 40 feet (12m) far in the direct rays of the sun]. These distances may vary.
The Case C: Operator stops sending control signals for more than one second.
6. In the case that several machines are operating in the same area, each machine should be
transmitting on a different infra-red channel.
7. Aflashinglightofthetransmitterblinksduring normal operation. A voltage drop of the
transmitter battery will cause the flashing light to alternate between on and off.
8. Hang-up the transmitter away from the machine for safety sake.
9. In operation with remote cable, do not pull out the cable strongly or run over it with the
machine.
10. Keep the transmitter away from the machine for safety sake.
11. To avoid excessive dust contamination of air cleaner, water may be used for dust control
in high dust areas.
12. To finish operation, be sure to switch off the main switch on receiver and press the emergency
stop button on transmitter.
13. When storing outside, keep the machine covered from the rain and always keep the
transmitter indoors.
J
NPA-919
No. Contents
1 LEFT FORWARD
2 LEFT BACK
3 RIGHT FORWARD
4 RIGHT BACK
5START
6 VIBRATION
No. Contents
7STOP
8 RECEPTION
9 CHARGE
10 OIL PRESSURE
11 OVERHEAT
12 SWITCH OFF
MONITOR LAMP LIST
OPERATIONAL CAUTION
1. Starting engine by electric starter
a. Ensure that the start switch is set at Cell-Start position and move main
switch to “ON” position.
b. Do not run starter longer than 10 seconds to avoid overheating.
c. Warmup the engine without load for 3 to 5 minutes.
2. Manually starting engine
a. Ensure that the start switch is set at Crank-Start position, and move main
switch to “ON” position.
b. Warm up the engine without load for 3 to 5 minutes.
3. To stop engine
a. Move stop switch to “OFF” position after running at idle for 3 to 5 minutes.
B. If engine does not stop properly, push the throttle lever next to the oil filter
until it comes to a completely stop, which takes approximately 15 seconds.
c. After operation is completed, move both control switches of machine and
controller to the “OFF” position
J
NPA-903
J
NPA-951
CAUTION
NR.
(RECIEVINGFAILURE LIGHT)
Theremote controloperationisrestricted toanarrowerarea thefurtheryouare from
themachine. Iftheoperativesignals donotreachthe plateproperly, RECEIVING
FAILURE LIGHTis immediatelyonandwill stoptheplatevibration automatically(the
enginewill continuerunning)
OP.
(OIL PRESSURE(ENGINE)FAILURE LIGHT)
If the engine oil is low or the hydraulic oil pump is out of order,
OIL PRESSUREFAILURE LIGHTis onandwill stoptheengineautomatically
Tif thealternatorand regulatorinengineare outoforder,REGULATORFAILURE
LIGHT ison,butthe machineisoperative. Besuretocheck themafteroperation
RE.
(REGULATORFAILURE LIGHT)
OH.
(E/GOVERHEATLIGHT)
Ifthe engineiscontinuously overloadedorifthe airelementisplugged duetoexcessive
dust,the machine E/GOVERHEATLIGHTwill light tonotify ofan engine overheat.To
correct, run the machine without vibration about 5 minutes or stop the engine for
cleaning air element. If this is not done the machine willstop vibrationautomatically
and continue to run without vibration for cooling the engine.
The vibrator willnot start againuntil theengine temperaturereaches andacceptable
level.
P/N:920109790
OH RE OP NR
J
NPA-925
P/N: 920109710
P/N: 920109710
P/N: 920109780
P/N: 920109780
P/N: 920209250
P/N: 920209250
P/N: 920109730
P/N: 920109730
P/N: 920209080
P/N: 920209080
P/N: 920102710
P/N: 920102710
MVH-RC
K
NPA-908
K
NPA-908
P/N: 920109720
P/N: 920109720
J
NPA-928
HYDRAULIC
OIL ONLY
HYDRAULIC
OIL ONLY
P/N: 920109810
P/N: 920109810
P/N: 920209310
P/N: 920209310
SAE 10W-40
Motor Oil
SAE 10W-40
Motor
Oil
J
NPA-748
P/N: 920209230
P/N: 920209230
N
P
A
-
3
3
3
J
P/N: 920203330
P/N: 920203330
MAIN SWITCH
NPA-904
J
P/N: 920109750
P/N: 920109750
K
NPA-907