Filter
Top Products
Electrical
requirements
Electrical ground is required
on this appliance.
Electric Shock Hazard
. Check with a qualified
electrician if you are in doubt as
to whether the appliance is
properly grounded. Improper
connection of the equipment-
grounding conductor line can
result in a risk of electrical
shock.
- Do Not use an extension cord
with this appliance. Such use
may result in a fire. electrical
shock or other personal injury.
* Do Not have a fuse in the neutral
or grounding circuit.
A fuse in
theneutral or grounding circuit
could result in an electrical
shock.
Failure to follow these instruction!
could result in a fire. personal
injury, or electrical shock.
Save Installation Instructions for
the local electrical inspector’s use.
A
Ths apphance must be
n
connected to the proper
electrical voltage and frequency as
specified on the seritiratmg plate
Models rated at 7 0 kw on 240 volts
(5 3 kw on 208 volts) 01 more require a
separate 40.ampere crcuit Models
rated at 3 6 !-xv on 240 volts (2.7 kw
on
208 volts) or less requne a separate
30.ampere cmxut. Fuse both sides of
the lme A tune-delay [use or cmxt
breaker IS racormmended
B
OVEN MUST BE CONNECTED
. WI’IH COPPER WIRE ONLY
C
Wire sizes must conform to
m the recruements of the
NatIonal Elect&l Code, ANSL+JFPA
70.latest edmon’, and all local codes
and ordumnces for the kilowatt rating
of the oven. This rating can be found
on the serial’ratmg plate behmd the
oven door on the front frame.
D
This apphance should be
9 connected to th.e fused
chsconma (or Cmxt breaker) box
through flexible armored or
non-metalhc, sheathed copper cable
fwlth aroundma wre) The flexible
&m&d cable &ten&g from the
apphance should be connected duectly
lo the junction box
E
Locate the lunctlon box to
. aLlow as much slack in the
cable as possible between the
lunctlon box and the apphance so that
the oven can be moved ti servlcmg is
ever needed
F
A U.L -hsted condux connector
must be provided at the
’ ~unctlon box
G
It 1s tte personal
n
responsiblbty and obhgation
of the customer to contact a quahfled
elennclan to assure that the klectrical
mstallatmn IS adequate and is m
conformance with the National
E!ectncal Code ANSI/NFPA 70.latest
edItIon*, and aL’local codes and
ordmmces
H
A wrong dagram is mcluded
m m the Tech sheet. The Tech
sheet 1s located oehmd the control
panel
Electrical
connection
Electrical ground is required
on this appliance.
4. Connect the groundmg wue to a
grounded wire 111 the ]unct~on box or to
a grounded, copper cold water Pipe **
Electrical Shock Hazard
- Do Not connect appliance to
electrical supply until appliance
is permanently grounded.
l
Disconnect power to the
junction box before making the
electrical connection.
n
This appliance must to
connected to a grounded.
metallic. permanent wiring
system, or a grounding
conductor should be connected
to the grounding terminal of
lead on the appliance.
I
Failure to follow these
I
jnstructions could result m a fire.
personal injury, or electrical
shock.
Tbs apphance 1s manufactured wxh
white (neutral) power supply wre and
a cabmet-connected. green groundmg
wre (green twisted together)
Connect the apphance cable to the
lunctmn box through the U L -hsted
conduit connector. Complete
electrical connection accordmg to your
mstallatmn needs
A. Where local codes
permit...
connecting the cabinet-grounding
conductor to the neutral (white)
junction box wire:
Figure 1
1. Turn power supply off
2. Connect three wires green and
whte apphance cable wLies with the
neutral (wtite) wne m junction box
3. Connect the two black wues
together, then the two red wues
together (See Figure 1 )
B. Where local codes
DO NOT permit...
connecting the cabinet-grounding
conductor to the neutral (white)
junctmn box wire:
Figure 2
1. Turn power suppiy off
2. Connect the white apphance cable
wue to the neutral (whxe) wue m
]unctlon box
3. Connect the two black wres
together; then the two red wnes
together (See Figure 2 )
Figure 3
5. A separate copper groundmg wxe
(No. 10 mmmum) MUST be connected
to a grounded metal cold water pipe by
means of a clamp and then to the
external groundmg mnnector screw.
Do Not ground to a gas
supply
pipe
or hot water pipe. Do Not connect
to electrical supply until appliance 1s
permanently grounded. (See
Figure 3 )
C. IF connecting to a
four-wire electrical
system...
DO NOT connect the cabinet-
grounding conductor to the neutral
(white) junction box wire.
Figure 4
1. Turn power supply off
2. Separate the green and wtite
appbance cable wues
3. Connect the white apphance cable
wue to the neutral (wtite) wre m
iuncilon box
4. Connect the two black wires
tooether. then the two red wres
together (See Figure 4.)
5. Connect the green apphance cable
wre to green groundmg wxe in the
]unctlon box
PANEL C