Filter
Top Products
10
To Start Brewing Coffee Immediately
1. For optimal holding temperature, rinse the inside of Thermal
Carafe with warm water before brewing; empty and make sure
the Carafe Lid Lever is at the back of the Carafe and the Lid is
properly secured. Place Carafe onto Base Plate, making sure it
is firmly set against the silver Auto Pause and Pour Assembly
of the Coffeemaker. (See Figure 1.)
2. Check to make sure the Removable Water Reservoir is filled;
correctly positioned and in place before starting.
3. Press the ON/OFF/AUTO Button. The blue BREW Light will
illuminate as the Coffeemaker begins brewing. Once the brew-
ing cycle is complete, the Coffeemaker will turn itself OFF.
To Start Brewing Coffee at the
Programmed Time
1. At the programmed time, the Coffeemaker will turn itself ON
automatically. The blue BREW Light will illuminate as the
Coffeemaker begins brewing. Coffee will begin flowing into
the Thermal Carafe. Once the brewing cycle is complete, the
Coffeemaker will turn itself OFF.
NOTE: The amount of coffee in the Carafe may be slightly less
than the amount of water placed in the Water Reservoir, since
some of the water is absorbed by the coffee grounds.
Auto Pause and Pour Feature
1. To pour a cup of coffee before the brew cycle is complete,
simply remove the Carafe from the Base Plate and pour.
Brewing will continue but dripping will automatically pause.
Return the Carafe to the Base Plate within 1 minute; dripping
will resume.
NOTE: The Thermal Carafe must be placed and centered onto the
Base Plate, the Carafe should rest firmly against the silver Auto
Pause and Pour Assembly of the Coffeemaker (see Figure 1) to
allow proper operation of the Auto Pause and Pour Feature.
2. Remove the Thermal Carafe from the Base Plate. Always keep
the Carafe Lid on the Carafe when pouring the coffee. Depress
the Thumb Lever and pour.
CAUTION: To avoid injury when using the Auto Pause and
Pour Feature while the Coffeemaker is still brewing, the
Thermal Carafe with Lid must be replaced on the Base
Plate, under the Filter Holder within 1 minute to prevent
the Filter Basket from overflowing.
7
Before Using Your
Programmable Coffeemaker
WARNING: To reduce risk of fire or electric shock, do not
immerse cord, plug or appliance in water or any other liquid.
1. Before preparing coffee in your new Coffeemaker, thoroughly
clean the Removable Water Reservoir, Thermal Carafe,
Carafe Lid, Removable Filter Holder and Permanent Filter
Basket in warm, soapy water. Rinse and dry thoroughly.
Replace clean disassembled parts.
NOTE: Do not dry the inside of the Removable Water
Reservoir with a cloth because this will leave a residue of
lint and may clog your Coffeemaker.
2. To replace the Removable Filter Holder into the Coffeemaker’s
Cavity, rotate the front tab so that it faces the front right of the
Coffeemaker. The Pause and Pour Lever, located on the
bottom of the Filter Holder, sits down into the back of the
Cavity; the single clip will be at the front of the unit. Press the
Filter Holder down into place. The Lid will be fully closed when
properly assembled.
3. Clean the inside of the Coffeemaker by brewing 2 full Carafes
of clean, cool water (see Brewing Instructions). Do not place
the Permanent Filter Basket or coffee in the Removable Filter
Basket for this initial cleaning.
NOTE: At the end of the first brewing cycle, press the
ON/OFF/AUTO Button to turn the Coffeemaker OFF and
wait 10 minutes for the appliance to cool. Empty Carafe and
replace onto Base Plate. Add fresh cool water to the Water
Reservoir. Press the ON/OFF/AUTO Button twice to turn the
Coffeemaker ON. The blue BREW Light will illuminate; brew a
second Carafe. Discard water. Your Coffeemaker is now ready
for use.
Melitta_ME10DTB_IB_3-5-05 5/3/05 2:22 PM Page 13