Traulsen RBF234HUT-FHS Refrigerator User Manual


 
-8-
TROUBLE
IX. a - INTRODUCTION:
Most Traulsen models are constructed with a high quality
430 series, 20 gauge stainless steel exterior finish (front,
sides and doors). The interior finish on these same mod-
els are constructed using 300 series stainless steel.
The stainless steel finish on Traulsen products should re-
tain its appearance throughout the products usable life-
time. However, some care is required to maintain this ap-
pearance. The following paragraphs will provide a guide-
line on proper care of the exterior/interior finish, as well as
some suggestions on how to repair a finish which has been
marred due to adverse environmental conditions or im-
proper jobsite care.
IX. b - STAINLESS STEEL, HOW IT WORKS:
The process by which stainless steel retains its appear-
ance is a result of its type of metal alloy. Steel is a compos-
ite of metals combined in a specific industrial process.
Stainless steel contains a high percentage of chromium,
the addition of which provides both its appearance, and a
microscopic surface layer protecting the steel underneath
from corrosion. This external layer acts as a barrier, pre-
venting typical oxidation of the steel. Remove this barrier,
and the environment will eventually corrode the metal,
marring its appearance.
IX. c -
UNDERSTANDING THE CAUSES OF CORROSION:
Corrosion to stainless steel can only be caused in one of
four specific ways:
1) ABRASION
Abrasion can be caused during routine cleaning of the
metal, either by use of an abrasive cleanser, or use of an
abrasive device, such as a metal scouring pad. Abrasion
can also be caused by contact with other hard surfaces,
such as nearby equipment, walls or tools. Special care
should be taken to position your unit properly to prevent
accidental dents and scratches.
2) WATER
Water everywhere contains various deposits, or solids,
which as the water drys or evaporates, can leave spots
behind. The spots may eventually cause corrosion if not
removed.
3) CHEMICALS OR WATER CONTAINING CHLORIDES
Chlorides, such as found in water or many cleaning mate-
rials are especially corrosive to stainless steel. Daily jani-
torial duties, such a floor mopping, can splash water con-
taining chlorinated cleansers against the front and sides
of a Traulsen refrigeration product, resulting in corrosion.
Avoid use of these on or around a Traulsen refrigeration
product if at all possible.
4) PROLONGED CONTACT WITH FOOD PRODUCT
Many food products, such as milk and carbonated sodas,
IX. STAINLESS STEEL OVERVIEW
IX. c - UNDERSTANDING THE CAUSES OF CORROSION:
contain acids which may damage the protective layer of
stainless steel. All food and beverage spills should be
cleaned up promptly to avoid possible stains and corro-
sion.
X. CARE OF STAINLESS STEEL
X. a - USING THE PROPER TOOLS:
Use of proper cleaning materials will do much to prolong
the appearance of your Traulsen refrigeration product. We
particularly encourage the use of either plastic scouring
pads or soft cloths for cleaning stainless steel.
Soft nylon scouring pads can also be used, however care
has to used to insure that all scrubbing is done in the di-
rection of the metals GRAIN. Because metals are
chrystalline in nature, when they are in a solid state the
individual ions line up to form visible grain lines. Use of a
soft nylon scouring pad in a direction opposite of the grain
will mar its luster. Always do so PARALLEL to the grain.
There are several types of tools which should
NEVER BE
USED when cleaning stainless steel, these include:
WIRE BRUSHES
METAL SCOURING PADS
SANDPAPER
SCRAPERS & PUTTY KNIVES
Use of any of these tools will result in scratches or removal
of the stainless steels protective layer, which will eventu-
ally lead to corrosion and rust.
X. b - USING THE RIGHT CLEANSER:
Avoid all cleaning products containing chloride ingredients.
Use of a cleanser specifically designed for stainless steel
is highly recommended. You may find yourself in a situa-
tion where you are uncertain if a particular cleaning prod-
uct contains any chlorides. If unsure, its probably best to
just assume that it does and avoid its use in cleaning a
Traulsen refrigeration product.
Also to be avoided are cleaning products which contain
QUATERNARY SALTS. These salts can literally attack
the stainless steels protective layer, leading to corrosion
and pitting of the steels surface.
After cleaning, it is important to always rinse the cleaned
area thoroughly with cool, clean water (do not use hot wa-
ter) and wipe completely dry using a paper towel or soft
absorbent cloth.
Use of cleaning products designed for use on stainless
steel, in conjunction with the proper tools, as outlined above
will help retain the appearance of your Traulsen refrigera-
tion product for years and years.