Filter
Top Products
14
4. Wash stainless steel and painted metal exteriors with a clean
sponge or soft cloth and a mild detergent in warm water. Do
not use abrasive or harsh cleaners. Dry thoroughly with a soft
cloth. For additional protection against damage to painted
metal exteriors, apply appliance wax (or auto paste wax) with
a clean, soft cloth. Do not wax plastic parts.
NOTE: To keep your Stainless Steel refrigerator looking like
new and to remove minor scuffs or marks, it is suggested that
you use the manufacturer’s approved Stainless Steel Cleaner
& Polish.
IMPORTANT: This cleaner is for Stainless Steel parts only!
Do not allow the Stainless Steel Cleaner & Polish to come into
contact with any plastic parts such as the trim pieces,
dispenser covers or door gaskets. If accidental contact does
occur, clean plastic part with a sponge and mild detergent in
warm water. Dry thoroughly with a soft cloth. To order the
cleaner, see the “Accessories” section.
5. There is no need for routine condenser cleaning in normal
home operating environments. If the environment is
particularly greasy or dusty, or there is significant pet traffic in
the home, the condenser should be cleaned every two to
three months to ensure maximum efficiency.
If you need to clean the condenser:
■ Remove the base grille (see “Base Grille” or “Door
Removal” section).
■
Use a vacuum with a soft brush to clean the grille, the
open areas behind the grille and the front surface area of
the condenser.
■
Replace the base grille when finished.
6. Plug in refrigerator or reconnect power.
Changing the Light Bulb
NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to
replace the bulb with one of the same size, shape, and wattage.
Changing the Refrigerator Light Bulb
1. Unplug refrigerator or disconnect power.
2. Remove screw from light shield. Make sure you keep screw
for reattaching.
3. Slide shield toward back of compartment to release from light
assembly.
4. Replace burned-out bulb(s) with an appliance light bulb no
greater than 40 watts.
5. Replace light bulb cover by inserting tabs on light shield into
liner holes on each side of light assembly. Slide shield toward
front of unit until it locks into place.
NOTE: Do not force shield beyond locking point; doing so
may damage light shield.
6. Replace screw.
7. Plug in refrigerator or reconnect power.
Changing the Freezer Light Bulb
1. Unplug refrigerator or disconnect power.
NOTE: May need to remove upper freezer shelf or basket to
access light assembly.
2. Squeeze and pull rear of light shield cover toward you to
release tabs and pull down.
3. Replace burned-out bulb with appliance bulb no greater than
40 watts.
4. Insert front tabs of light cover into liner and snap back portion
over light assembly.
5. Plug in refrigerator or reconnect power.
Power Interruptions
If the power will be out for 24 hours or less, keep both refrigerator
doors closed to help food stay cold and frozen.
If the power will be out for more than 24 hours, do one of the
following:
■ Remove all frozen food and store it in a frozen food locker.
■ Place 2 lbs. (907 g) of dry ice in the freezer for every cubic
foot (28 L) of freezer space. This will keep the food frozen for
two to four days.
■ If neither a food locker nor dry ice is available, consume or
can perishable food at once.
REMEMBER: A full freezer stays cold longer than a partially filled
one. A freezer full of meat stays cold longer than a freezer full of
baked goods. If you see that food contains ice crystals, it may be
refrozen, although the quality and flavor may be affected. If the
condition of the food is poor, dispose of it.
Vacation and Moving Care
Vacations
If you choose to leave the refrigerator on while you’re
away:
1. Use up any perishables and freeze other items.
2. If your refrigerator has an automatic ice maker:
■
Raise wire shutoff arm to OFF (up) position or move the
switch to the OFF (right) setting.
■
Shut off water supply to the ice maker.
3. Empty the ice bin.