Filter
Top Products
7.
terminal
bOX
cover
6
m
Remove terminal box Cover from
Mae than one person is required to help
with appliance intiallation because Of its
weight and size.
Failure to tallow these instructions may
result in personal injury.
Numbers
correspond
to steps.
n
To vent through wall with 3- 1 /A” X 10”
rectangular ductwork, measure from floor
65-7/r and 62-3/8” (or l/8” and 3-5/8” dOW
from underside of cabinet) and mark on
back wall, Measure and mark a line !5-1/4”
to right and left of centerline connecting
‘the two lines, Use a saber SUW t0 Cut a
rectangular opening for the ductwork.
31,
n rm
Install ductwork through the vent opening in
upper
cabinei or wall. Complete venting
system according to method needed. See
*\/entina requirements.
N Use caulking to
7
Lift the range hood into final
l position and center. Mark on the
nderside of cabinet the location of the
3 hole mounting slots. set IOn”* hnnrl
?k ,I protected surface.
U’
four kc
aside L. ( - r
Ta wire through rear, mark a line 7-l /2” from
the right of the centerline on the Wall. Mark
the point on
this line that is 64-s/8” from the
floor (or I -3/8” from underside of cabinet).
Drill a T-1 /4” diameter hole through Wail at
this point’
I&
m
,Kach rectangular damper to selectea
>.ctanguiar vent opening, If damper is
&ached to back of range hood, be Sure
jamper hinge is toward the top. Far round
ented installations, use round damper in
juct to prevent air from flowing back into
juclwork, If roof cap has a damper,
-‘-.-rrh, k-‘....Ac’^
Cm,-,-, rnnne hood,
8
m
Determine and clearly mark a vertical
centerline on the wall and cabinet in the
area the vent opening will be made.
To vent through the roof with 7”
round
ducfwark mark 4-l /2” and 5” in from back
wait atoni the centerline on underside Of
cabinet, Use these points as centers t0
draw 7-1 /g” circles on underside of cabinet.
Use a saber saw to cut the openings for the
ductwork Repeat for the underside of the
top of the cabinet, This will create slotted
4
4
13
m
Run wiring through wall of cabinets
according to the National Electricai
Code
and local codes and ordinances.
DO Not
turn on power until installation is complete.
openings,
keyhole slot
To wire throl
To wire through top, mark a line
7-112” from
the righ. _ ”
the right of the centerline on the underside
of the c
of the cabinet, Mark the point on this tine
the
that is l-3/8” from back wall. Drill a 1-l /4”
diameter hole through the cabinet at this
die,..-.-.
Start screws through neck of each of the
four keyhole mounting screw slots marked
on the cabinet bottom,
point.
Lift
elc
PO
7;
the
Tic
ml
,, _._-
ne-.. _
if used, rot&es up and down treW~
-range hood into final position, feeding
bctrical wire through wiring opening,
&ion the range hood so that the large
,d of the keyhole slots are over the screws,
en push the hood toward the wall SO that
e screws are in the neck of the SlOtS.
lhten mounting screws to cabinet,
oking sure mounting screws are in narrow
!ck of slots, Make sure that damper blade.
To vent through the roof with 3-j /4” X
10
rectangular ductwork, mark a line 1” and 5”
from the buck wall on the underside of the
cabinet Mark lines 5-l /4” to the right and
left of the centerline on the underside of
cabinet that connect the lines just drawn.
Use a saber saw to cut a
EdangUlar
opening far the ductwork. Repeat for the
underside of the top of the cabinet,
Panel C