Whirlpool 3369089 Dishwasher User Manual


 
Recommended drain hose
connection methods:
Drain hose to air gap to waste tee.
15
Check door for proper
w operation. Door should
close easily without slamming and
open with its own weight. If neces-
sary, close door and adjust both
door springs by moving spring ends
to different holes in base.
clearance
t
above hap
Do Not solder within 6” of plastic
w at eT
Failure to follow this instruction
could result in product damage.
Drain hose to air gap to disposer.
16
Take a few minutes to
w read the Use and Care
Guide to fully understand your new
dishwasher.
IO
Connect water pipe or
n
tubing directly to water
inlet valve. Do Not run pipe or
tubing across front of motor or
dishwasher legs. Turn on water
supply and check for leaks.
17
Check that all parts have
w been installed and no
steps were skipped. Check that you
have all the tools you started with.
11
Check electrical require-
= ments. Be sure you have
correct electrical supply and recom-
mended grounding method. See
Panels A and B for proper connec-
tions.
18
Turn on electric supply.
w Start dishwasher and
allow it to complete a cycle. Check
that dishwasher is working properly
and that there are no water leaks.
Install air gap (Part No. 300096)’
according to kit instructions. If other
brands of air gaps are used, they
should be checked to make sure
they allow for the same water flow.
Connect the air gap to a waste tee
(Part No. 675149)’ or disposer using a
rubber connector (Part No. 674381)‘.
Most disposers have 7/8” connectors
or special connectors are avallable
at plumbing supply houses.
Be sure
to remove the disposer plug before
connecting the drain hose.
Alternate drain hose
connection methods:
lop mounting
brackets
attached to
underside of
countertop
Phillips
d
head
I
screws
No.
,0x,,2”
_--‘- -- :
,
19
Replace the access
w panel and toe panel
Do not r,
drop
l
.-
screws
<+
into tub.li~~-- .___- ‘;‘ 3
12
-1~.
Open dishwasher door
n
and remove all shippina
20
If changing color of door
n
and access panel or
installing custom panels, follow the
“To change door and access panel
color- instructions, Panel E.
Drain hose to waste tee.
Cut hose
Waste tee
- Aonnec!or
materials. Remove bottom rack. -
Place a newspaper or large sheet
of paper over bottom of dishwasher
to protect the pump area when
securing dishwasher to countertop.
13
Secure dishwasher to
n
countertop with two No.
10 x l/2” Phillips-head screws from
parts bag. You
MUST
secure
dishwasher to keep it from tilting
when door is opened or closed. Do
Not drop screws in dishwasher tub.
If screws should fall into the pump,
pump and motor failure may occur.
Remove paper from bottom of
dishwasher.
If local plumbing codes permit,
dishwasher drain hose may be
connected directly to waste tee
(Part No. 675149)‘. The waste tee
connection MUST be made ahead
of the trap and a minimum of 20
inches above the floor.
/
equally spaced
Do Not
“cut hose
connector.
Screw-type clamp
20” min.
clearance
to floor
You have just
finished installing your
new Whirlpool
Undercounter Dishwasher.
+
Entry must be
above trap
If local plumbing codes permit,
dishwasher drain hose may be
connected directly to a disposer.
Most disposers have 7/V connectors
or special connectors are available
at plumbing supply houses.
Be sure
to remove the disposer plug before
connecting the drain hose.
l
All parts are available through your
dealer.
\\
ii
14
Open door approximately
w 3” and check for equal
spacing between inner door and tub
sides. If necessary, loosen screws that
fasten dishwasher to countertop and
shift tub. Tighten screws.
Congratulatfons!
J
Keep Installation Instructions
available for easy
reference.
/
Panel D