Filter
Top Products
To change access
color panel
(For models so equipped)
Personal Injury Hazard
Wear gloves and handle panels
carefully.
Cut metal edges may cause personal
injury or damage to other materials.
&Pushup m
wrth thumbs on
each end of
access panel
top trim to
unsnap trim.
Remove top trim and set it aside.
2
n
Carefully
slide color
I II
3
n
With
desired color
facing out, bow
access panel
and insert into
access panel
access panel
upwards and
remove. Do Not
remove spacer.
frame. Slide panel down into groove
along bottom of access panel frame.
4
n
Line up
edges of top trim
with sides of
access panel
frame. Tilt back of
trim down and slide into place. Snap
front of trim down to cover top edge of
access panel.
To install
customized wood
panels in door and
access panel
Dishwasher door panel and access
panel (if model is so equipped) can be
customized to match wood cabinets. A
standard l/4” (7/32” actual thickness)
wood panel can be used as is for
customizing the door and access
panels.
A door panel thicker than 7/32”,
requires routing the top and bottom to a
7/32” thickness.
An access panel thicker than 7/32”,
requires routing all four edges to a 7/32”.
It is recommended that a cabinet-
maker cut the customized panels
because of the precise cuts required.
(See Figures 4 and 5.)
Wood door panel
Cut accurately for a snug fit between
door side frames. Note: Custom panel
fits between, Not inside frame.
This panel
is narrower
than
access
panel.
File or sand
edges of
;~;oye’
slivers.
bottom
edge
Figure
clear access pan-
when door is in
I I
open position.
I I
Heavy-duty door springs must be used if
custom door panel weighs more than 4
pounds. Heavy-duty Door Springs Kit,
Part No. 4318050, is available from your
dealer or parts supplier. Maximum door
weight is 8 pounds.
Wood access panel
This panel is wider that door panel.
k- 23-5/I&
I
4-7116
All edges routed to 7/32” thickness.
Top view
&7/W thick
1
Figure 5
n
Cut wood door and access panels
using specified dimensions. Make sure
wood grain direction matches cabinet
wood grain.
2
n
File or sand edges of wood panels
to avoid slivers.
Dishwasher is subject to some humidity.
Cover both sides and edges of wood
panels with moisture-resistant sealer.
Personal Injury Hazard
Wear gloves and handle panels
carefully.
Cut metal edges may cause personal
injury or damage to other materials.
3
n
Insert finger
I rnrbr nne tad nf
-. - .- -. - r -..
towards you in a
peeling action. Set
retainer aside.
4
Lift door panel(s)
n
at outer edges.
Use one hand to bow
bottom of panel(s).
Remove panel(s) and
spacer. Save panel(s)
and spacer for future use
top of panel
under control
console
panel fits
bet&en,
not inside, door frame
n
Insert top of wood door panel
between sides’of door frame about 3”
below console. Rotate wood door panel
down against dishwasher door. Slide top
edge of wood door panel under bottom
edge of console. Press lower portion of
wood door panel in place between sides
of door frame, allowing wood door panel
to rest on channel at bottom of door.
Snap into
Push in
channel.
along
length of
retainer. _
6
Snap one end
ofsainer into
-
n
channel as shown. Push inward
while sliding thumb along full length of
retainer.
w Check door for proper
operation. Door should close easily
without slamming and open with its own
weight. If necessary, close door and
adjust both door springs by moving
spring ends to different holes in base.
8
n
Push up with
thumbs on each end
of access panel top
trim to unsnap trim;
Remove top trim and set it aside.
9
n
Carefully slide
color access panel
and spacer
upwards and
remove. Save color access panel and
spacer for future use.
10
n
Insert wood access panel into
access panel frame. Slide panel down
into groove along bottom of access
panel frame. It may be necessary to
remove the two screws securing top of
access panel to dishwasher frame and
tilt access panel forward to install some
wood panels.
edges of top trim
with sides of access
panel frame. Tilt
back of trim down
and slide into place. Snap front of trim
down to cover top edge of wood
access panel.
Panel E