Filter
Top Products
9
Never try to remove the
pusher, lid and work bowl
together; as a safety
feature, the pusher
assembly must be removed
before the lid and work
bowl can be unlocked.
They can then both be
unlocked at the same time.
Remove the bowl from the
base of the machine before
removing the blade. This
creates a seal to prevent
food from leaking. Turn the
bowl clockwise to unlock
from the base, and lift
straight up to remove.
To prevent the blade from
falling from the work
bowl onto your hand
when emptying the work
bowl, use one of the fol-
lowing methods. Be sure
your hands are dry.
Grab the blade hub, and
remove the metal blade
before tilting the bowl,
using a spatula to scrape
off any food. Then carefully
lift the blade out of the
work bowl. Or insert your
finger through the hole in
the bottom of the work
bowl, gripping the blade
from the bottom, and grip
the outside of the work
bowl with your thumb. Or
hold the blade in place with
your finger or spatula while
pouring out food.
TECHNIQUES FOR
CHOPPING AND
PURÉEING WITH
THE METAL BLADE
To chop raw fruits
and vegetables:
First cut the food into
1-inch (2.5 cm) pieces.
You get a more even
chop when all pieces are
about the same size.
Put no more than the
recommended amount of
food into the work bowl
(see table inside front
cover). Lock the cover in
place. Press the “Pulse”
button at the rate of 1
second on, 1 second off,
until the food is coarsely
chopped. For more finely
chopped results, hold
the “Pulse” button, letting
the machine run continu-
ously until the desired
consistency is reached.
Check frequently to avoid
overprocessing. Use the
spatula to scrape down the
sides of the work bowl if
necessary.
To purée fruits and
cooked vegetables:
First, cut the food into
1-inch (2.5 cm) pieces.
You get a smoother purée
faster when all pieces are
about equal in size.
Put no more than the
recommended amount of
food in the work bowl (see
table inside front cover).
Lock the cover in place.
“Pulse” to chop coarsely,
then press the “On” button
and process continuously
until food is puréed.
(NOTE: Cooked potatoes
are an exception to this
procedure. They develop
a gluey texture when
processed with the
metal blade.)
When making soup, you will
want to purée vegetables
that have been cooked in
liquid. Don’t add the liquid
to the work bowl, just the
cooked vegetables; remove
vegetables with a slotted
spoon. They will purée
faster and smoother without
liquid. Then add just enough
liquid to make the purée
pourable, return to the soup
liquid and stir to combine.
To dislodge food:
O c c a s i o n a l l y, a piece of
food may become wedged
between the blade and the
work bowl. If this happens,
unplug the machine, remove
the cover, lift the blade out
carefully and remove the
wedged piece. Empty the
bowl, reinsert the blade and
lock the cover into place,
then insert the pusher. Press
the “On” button and drop the
food pieces through the
small feed tube opening
while the machine is
running. After adding a
cupful (250ml) this way, add
the remaining food to the
bowl and process in the
usual manner.
To chop hard foods:
To chop hard food like
garlic and hard cheese,
assemble the unit, remove
the small pusher, press the
“On” button and drop the
food through the small
feed tube while the machine
is running.
Small foods like garlic can
be dropped in whole. Large
foods like hard cheese
should be cut into 1-inch
(2.5 cm) pieces. This method
of processing minces garlic,
shallots and onions. Hard
cheese and coconut will
have the same texture as if
they had been hand grated.
IMPORTANT: Never try to
process cheese that is too
hard to cut with a knife.
You may damage the
blade or the machine.
To chop parsley and
other fresh herbs:
The herbs, the work bowl
and the metal chopping
blade must all be thoroughly
clean and dry. Remove
stems from herbs. A d d
leaves to bowl and process,
DLC-2011C IB-3622-CAN-B sc 10/5/02 10:01 AM Page 10