Filter
Top Products
10
Danger of burns!
During rinsing, a little hot water ows from the coee spouts.
Avoid contact with splashes of water.
• To turn the appliance o, press the button (g. 8).
• The message “Turning o, Please wait” is displayed: if fea-
tured, the appliance completes a rinse cycle and then goes
o (standby).
Please note!
If you will not be using the appliance for some time, unplug
from the mains socket:
• rst turn the appliance o by pressing the button
(g. 8);
• release the main switch at the back of the appliance (g.
2).
Important!
Never press the main switch while the appliance is on.
MENU SETTINGS
When you access the settings menu by pressing the MENU/ESC
button, scroll the menu items by pressing < or > (g. 9).
Rinsing
Use this function to deliver hot water from the spout to heat the
internal circuit and make the coee delivered hotter.
To enable the function, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press < or > (g. 9) until “Rinsing” is displayed;
3. Press the OK button: “Conrm?” will be displayed.
4. Press the OK button (g. 10): after a few seconds, hot water
ows out of the spout, heating the internal circuit and ma-
king the coee delivered hotter.
Please note!
Press any button to stop hot water delivery at any time.
Descaling
For instructions on descaling, see page 18.
Install lter
For instructions on how to install the lter, see the section
“Water softener lter” (page 19).
Replacing the lter (if installed)
For instructions on how to replace the lter, see the section “Re-
placing the lter” (page 20).
Adjust time
To adjust the time on the display, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press < or > (g. 9) until “Adjust time” is displayed;
3. Press the OK button (g. 10): the hours ash;
4. Press < or > (g. 9) to change the hours;
5. Press the OK button to conrm: the minutes ash;
6. Press < or > (g. 9) to change the minutes;
7. Press the OK button to conrm.
This sets the time. Press the MENU/ESC button to exit the menu.
Auto-start
You can set the auto-start time in order to have the appliance
ready at a certain time (for example in the morning) so you can
make coee immediately.
Please note!
To enable this function, the time must already be set correctly.
To enable auto-start, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press < or > (g. 9) until “Auto-start” is displayed;
3. Press the OK button. “Enable?” is displayed;
4. Press the OK button to conrm;
5.
Press < or > to choose the hours;
6. Press the OK button to conrm;
7. Press < or > (g. 9) to change the minutes;
8. Press the OK button to conrm;
9. Then press the MENU/ESC button to exit the menu.
Once the time has been conrmed, activation of auto-start is
indicated by the symbol displayed alongside the time.
To disable the function:
1. Select auto-start from the menu;
2. Press the OK button. “Disable?” is displayed;
3. Press the OK button to conrm.
The symbol is no longer displayed.
Auto-O (standby)
Auto-o mode can be set, so that the appliance switches o
when not used for 15 or 30 minutes, or 1, 2 or 3 hours.
To programme Auto-o, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press < or > (g. 9) until “Auto-o” is displayed;
3. Press the OK button;
4. Press < or > (g. 9) until the required operating time (15
or 30 minutes, or 1, 2 or 3 hours) is displayed;
5. Press the OK button to conrm;
6. Then press the MENU/ESC button to exit the menu.
Auto-o is programmed.
Cup warmer
This function allows the cup warmer to be enabled or disabled.