Filter
Top Products
4
7. INSTALLING REFRIGERATOR IN
ENCLOSURE
NOTE: DO NOT install the appliance directly on carpet-
ing. Carpeting must be removed or protected by a
metal or wood panel beneath the appliance, which
extends at least the full width and depth of the appli-
ance.
The dimensions shown in FIG. 3 will give
you adequate space for service and proper
installation.
e
RefrigeratorRefrigerator
RefrigeratorRefrigerator
Refrigerator
OverallOverall
OverallOverall
Overall
InstallationInstallation
InstallationInstallation
Installation
RecessRecess
RecessRecess
Recess
ModelModel
ModelModel
Model
DimensionsDimensions
DimensionsDimensions
Dimensions
DimensionsDimensions
DimensionsDimensions
Dimensions
DimensionsDimensions
DimensionsDimensions
Dimensions
RM2191RM2191
RM2191RM2191
RM2191
HeightHeight
HeightHeight
Height
WidthWidth
WidthWidth
Width
DepthDepth
DepthDepth
Depth
HeightHeight
HeightHeight
Height
WidthWidth
WidthWidth
Width
DepthDepth
DepthDepth
Depth
HeightHeight
HeightHeight
Height
WidthWidth
WidthWidth
Width
DepthDepth
DepthDepth
Depth
RM2193RM2193
RM2193RM2193
RM2193
AA
AA
A
BB
BB
B
CC
CC
C
hh
hh
h
ww
ww
w
dd
dd
d
HH
HH
H
WW
WW
W
DD
DD
D
(Inches) 21-9/16 18-13/16 21-7/16 20-5/8 17-1/2 19-7/8 20-7/8 17-3/4 20-7/8 1/4"
(mm) 548 478 545 524 445 505 530 451 519 6
Distance betweenDistance between
Distance betweenDistance between
Distance between
top of condenser andtop of condenser and
top of condenser andtop of condenser and
top of condenser and
top of refrigeratortop of refrigerator
top of refrigeratortop of refrigerator
top of refrigerator
ee
ee
e
A. INSTALLATION
The refrigerator must be installed in a substantial enclo-
sure and must be level. When installing the refrigerator in
the enclosure, all areas within the recess in which the
refrigerator is installed must be sealed from the living
space.
Make sure that there is a complete seal between the front
frame of the refrigerator and the top, sides and bottom of
the enclosure. A length of sealing strip is applied to the rear
surface of the front frame for this purpose. Also apply a
sealing strip to the foremost floor of the enclosure and
apply a second sealing strip to the bottom of the trim strip
on the front base as shown in FIG. 4. The sealing should
provide a complete isolation of the appliance's combustion
system from the vehicle interior.
B. CONDENSATE DRAIN HOLE:
A hole must be drilled through flooring "L" (FIG. 2). This
hole must be drilled in the one-inch clearance "M" (FIG. 2).
The installer MUST make sure that the hose does not kink
when run through the floor. Seal around the hose that goes
through the drilled hole. If a longer hose than supplied is
required to get the water to drain outside of the vehicle, the
installer will have to supply the extra length hose.
FIG. 4FIG. 4
FIG. 4FIG. 4
FIG. 4
NOTE: Be careful not to damage the sealing strip applied
to the floor of the enclosure when the refrigerator is put in
place.
FIG. 3FIG. 3
FIG. 3FIG. 3
FIG. 3