Filter
Top Products
1010
1010
10
Step 6Step 6
Step 6Step 6
Step 6
For rFor r
For rFor r
For r
ectangular ducted discharge installations onlyectangular ducted discharge installations only
ectangular ducted discharge installations onlyectangular ducted discharge installations only
ectangular ducted discharge installations only
(otherwise skip to next step)
Attach exhaust adaptor/damper Attach exhaust adaptor/damper
Attach exhaust adaptor/damper Attach exhaust adaptor/damper
Attach exhaust adaptor/damper over knockout
opening with two exhaust adaptor screws. Make
sure
damper
pivot pivot
pivot pivot
pivot is nearest to
top/back edge top/back edge
top/back edge top/back edge
top/back edge of hood.
Remove
tape tape
tape tape
tape from damper flap.
Exhaust
transition/damper
Pivot
Top/back
edge
NOTE: NOTE:
NOTE: NOTE:
NOTE: The exhaust adaptor/damper can be installed
up to 1 inch on either side of the hood center to
accommodate off-center ductwork. In extreme off-
center installations, one end of the duct connector
may need to be trimmed to clear the electrical cable
clamp.
Step 7Step 7
Step 7Step 7
Step 7
For rFor r
For rFor r
For r
ound ducted discharge installations onlyound ducted discharge installations only
ound ducted discharge installations onlyound ducted discharge installations only
ound ducted discharge installations only
Re-install the
rr
rr
r
ound transition ound transition
ound transition ound transition
ound transition with its screws.
7" Round
Transition
NOTE: NOTE:
NOTE: NOTE:
NOTE: The round transition can be installed up to 1
inch on either side of the hood center to
accommodate off-center ductwork. In extreme off-
center installations, one end of the duct connector
may need to be trimmed to clear the electrical cable
clamp.
Step 8Step 8
Step 8Step 8
Step 8
Mark holesMark holes
Mark holesMark holes
Mark holes
Select the vent option that your installation will
require and proceed to that section:
Outside top exhaustOutside top exhaust
Outside top exhaustOutside top exhaust
Outside top exhaust
(Vertical duct– 3 1/4”x 10” Rectangular)
Use the diagram or the hood as a template and mark
the locations on the cabinet for ductwork, electrical
wiring and keyhole screw slots.
Hood mounting screws (4)
1 1/4"
"
"
"
Center
line
Electrical access hole
(in cabinet bottom)
Wood shims (recessed
bottom cabinets only)
Vertical duct
access hole
13 15/16" (30" Hood)
16 15/16" (36" Hood)
13 15/16" (30" Hood)
16 15/16" (36" Hood)
Cabinet front
10 1/2"
Electrical access hole
(in
cabinet bottom)
5"
1 1/4"
Cabinet Bottom
12 9/16"
5 1/4"
5 1/4"
2"
Outside top exhaustOutside top exhaust
Outside top exhaustOutside top exhaust
Outside top exhaust
(Vertical duct–7” Round)
Use the diagram or the hood as a template and
mark the locations on the cabinet for ductwork,
electrical wiring and keyhole screw slots.
Hood mounting screws (4)
1 1/2"
"
Center
line
Electrical access hole
(in cabinet bottom)
Wood shims (recessed
bottom cabinets only)
13 15/16" (30" Hood)
16 15/16" (36" Hood)
13 15/16" (30" Hood)
16 15/16" (36" Hood)
Cabinet front
10 1/2"
Electrical access hole
(in
cabinet bottom)
Cabinet Bottom
12 1/2"
2 1/4"
8" DIA.
HOLE
5"
Access
hole for 7"
round duct
Installing the hood