Fisher & Paykel GC901 Cooktop User Manual


 
DIMENSIONS AND CLEARANCES
3
PRODUCT AND CUTOUT DIMENSIONS
GC36 GC901/GC901M
A
36” (914mm) 36” (914mm)
B 21” (533mm) 21
1
/
2
" (546mm)
C 1
5
/
8
" (41.5mm) 2
9
/
16
" (65mm) GC901,
3" (76mm) GC901M
D 19
1
/
2
" (494mm) [18
3
/
8
" - 19
3
/
4
"] 19
1
/
2
" (494mm) [19
1
/
8
" - 20
5
/
8
"]
E 34
1
/
4
" (870mm)
[33
3
/
8
" - 34
3
/
4
"]
34
1
/
4
" (870mm)
[33
7
/
8
" - 35
1
/
4
"]
F R
3
/
8
" (10mm) R
3
/
8
" (10mm)
G 1
3
/
16
" (30mm)
3
/
4
" (20mm)
H 1" (25mm) 1" (25mm)
US
CLAMPING DOWN THE COOKTOP
Place the cooktop into the cutout
and tighten it with the supplied
clamps. These will cope with the
countertop thicknesses
3
/
4
"- 2"
when used in the two orientations
shown.
Do not over tighten.
C
B
A
D
E
H
G
F
manifold
center line
gas inlet
a
b
d
c
e
i
h
g
j
a
36" = Minimum horizontal distance between overhead
cabinets installed on either side of this appliance.
b 30" = Minimum clearance from combustible surface centered
above the cooktop.
c 13" = Maximum overall depth of overhead cabinetry.
d 18" = Minimum clearance from countertop to overhead cabinetry.
e 4" (GC36) or 1
1
/
2
" (GC901 & GC901M) = Minimum clearance
from cooktop to the left side wall.
f 1" = Minimum clearance from cooktop to the right side wall.
g 1
1
/
2
" (GC36) or 1
1
/
4
" (GC901 & GC901M) = Minimum clearance
from cooktop to the rear wall.
h 2
1
/
2
" (GC36) or 1
1
/
4
" (GC901 & GC901M) = Minimum distance
from front edge of counter to front edge of appliance.
Where this reduces the distance between the back edge of the
appliance and the adjacent wall to less than the minimum of
1
1
/
2
" (GC36) or 1
1
/
4
" (GC901 & GC901M), this wall must be of
non combustible material (see note below).
i 2
3
/
8
" (GC36) or 3
5
/
16
" (GC901 & GC901M) = Minimum clearance
below countertop to any combustible surface.
j 30" = Maximum distance to nearest grounded power outlet
from the center of the cooktop.
The power cord must not touch any hot metal sufaces.
f
CLEARANCES
NON COMBUSTIBLE MATERIAL
Recommended non combustible materials are:
1
/
4
" (6mm) flame
retardant millboard covered with not less than No. 28 MSG sheet
steel, 0.015” (0.4mm) stainless steel, 0.024” (0.6mm) aluminium
or 0.020” (0.5mm) copper.
3
/
4
" - 2"