Filter
Top Products
6
Appliance InstallationAppliance Installation
Appliance InstallationAppliance Installation
Appliance Installation
(Note: two people may be required for proper installation of model FIJI).
8.8.
8.8.
8. Install transition to top of hood (if removed for shipping). Snap damper
into transition, foam tape up , with firm pressure at either end. Mark
onto exterior of transition the 'V' location of the damper within. See
Figure 6.
Note: Duct screws can ONLY go below this line.Note: Duct screws can ONLY go below this line.
Note: Duct screws can ONLY go below this line.Note: Duct screws can ONLY go below this line.
Note: Duct screws can ONLY go below this line.
9.9.
9.9.
9. Adjust chimney mounting structure to
SS
SS
S dimension as determined in
Step 1, page 5. Use 2 screws per attachment leg. Do not fasten to ceiling
now.
10.10.
10.10.
10. Set chimney mounting structure on top of hood canopy. Attach nuts
loosely. See Figure 8 and 9.
11.11.
11.11.
11. Fit duct piece on transition so that top end is 5-1/2" below top of
chimney structure, male end up.
12.12.
12.12.
12. Remove chimney structure from hood canopy.
13.13.
13.13.
13.
Install Ducting.Install Ducting.
Install Ducting.Install Ducting.
Install Ducting. Fasten duct to transition with screws and tape per code.
Loosely fasten starter collar (included) flush to top of duct. Note: screws
must not hamper the damper (see
8.8.
8.8.
8. above for screw location).
Loosely fasten starter collar (included) flush to bottom of duct.
14.14.
14.14.
14.
To install Chimney StructureTo install Chimney Structure
To install Chimney StructureTo install Chimney Structure
To install Chimney Structure to ceiling, use a 10mm or adjustable
wrench or flat head screwdriver. Drill pilot holes into ceiling. Attach
mounting structure to joists with the 4 lag screws provided. (Keep 1/2"
conduit inside structure.) See Figure 3.
15.15.
15.15.
15.
Remove Chimney Cover's plastic protective film.Remove Chimney Cover's plastic protective film.
Remove Chimney Cover's plastic protective film.Remove Chimney Cover's plastic protective film.
Remove Chimney Cover's plastic protective film. Reassemble and
fasten all 3 covers together with one vertical screw. See Figure 7. Slide
over chimney structure and secure with 2 screws near ceiling.
16.16.
16.16.
16.
To fasten the canopyTo fasten the canopy
To fasten the canopyTo fasten the canopy
To fasten the canopy use a 10mm or adjustable wrench. Affix nuts to
top of canopy.
Do not tighten.Do not tighten.
Do not tighten.Do not tighten.
Do not tighten. Raise canopy up to chimney structure and twist in place.
See Figure 9. Tighten nuts securely.
17.17.
17.17.
17.
Ducting for all units:Ducting for all units:
Ducting for all units:Ducting for all units:
Ducting for all units: There should be no more than 1" gap between
canopy ducting and house ducting. Adjust starting collar over both
ducts. Tighten collar. Fasten duct with screws and tape per code. Make
final angular adjustment to unit at ceiling if necessary, then securely
tighten 4 ceiling lag screws if not already tightened.
InstallationInstallation
InstallationInstallation
Installation
D
F
E
Figure 6Figure 6
Figure 6Figure 6
Figure 6
Figure 7Figure 7
Figure 7Figure 7
Figure 7
Figure 8Figure 8
Figure 8Figure 8
Figure 8
Figure 10Figure 10
Figure 10Figure 10
Figure 10
Figure 9Figure 9
Figure 9Figure 9
Figure 9