Filter
Top Products
Operating the Self-Cleaning Oven
Set the Oven for Cleaning
If range is too hot and you start to
set a clean cycle, the word “OFF”
will appear in the display. Allow
additional time for cooling before
you try to set the cycle.
NOTE: Only one oven at a time
can be self-cleaned.
“OFF”
wiH
appear in the display if you try to
clean both ovens at the same time.
1. Close the oven door
compl.etel.y.
2. Touch the CLEAN pad.
3. Touch INCREASE or
DECREASE pad.
“3:00,”
“HJ?”
and “TIME CLEAN” will appear
on display. Three hours is the
programmed clean time, but
any
time between two and four hours
can be set.
The door latches automatically.
If the oven door is not closed, the
word “DOOR” is displayed, the
word “LOCK” will flash
ad
the
oven will signal. Close the door.
The signal will stop and the
clean.
cycle will start when the door
can lock.
When a clean cycle is finished, the
word “CLEAN” will be off
in the display.
You
will
not
be able to open the
door unless the oven temperature
i.s
at a safe level, when “LOCK”
goes out on display. Wait until the
oven
has cooled. below locking
temperature (about 20-30 minutes).
NOTE: You can
fj.nd
out when the
clean cycle
will.
be finished by
~u~h,i,n,g
the STOP
THv!E
pad.
TO
Set a Delayed Start
1.
Close
the
oven.
door
com.pl.etely.
2.
Touch
the CLEAN pad.
3.
Touch. INCREASE
or
DECREASE pad to enter
CJ.ean
Time.
4. Touch STOP
TIME pad. “SET
STOP TIME” and. the
ear].iest
stop
time you can set
will
appear
on
djsplay.
The ea~l.j.est
stop
tjrne
will
be
the
clean
tj.m.e
selected. plus the
tjrne
of
da.~.
For
example:
j.~
the
clean tj.rne
is
t~.ree
hOIJM
and
the
time
of
day
is
6:00,
the
stop
time
that appears
on
di.spl.ay
will. be
9:00.
5.
~OUCb
INCREASE pad. to
change
the
stop
tjme
02
a. later tkne
of
clay
if
desir~d.
For example: if
you
set.
stop
tkne
at
1.1
:00,
oven
will
start
cl”em
cycle
a.t
8:()()
and
end a.t 1.1.:00.
NOTE:
During a. delayed
sel.f-
cl.ean
operation you. can find out
when
the oven is set to
tu..m
on
by
p~lshing
and. holding the
CJ_EAN
pad for
3
seconds.
To
Stop a
Clean.
Cycle
1.
Press the
CLEAIUOFF
pad.
After Self-Cleaning
You may notice some white ash
in the oven.
Just wipe it up with.
a damp
cloth
after the oven cools.
If white spots remain, remove
them with a soap-filled steel wool
pad. Be sure to
rhse
thoroughly
with a vinegar and water mixture.
These
deposits are usually a salt
residue that
carmot
be removed
by the clean cycle.
If the oven is not clean after one
clean cycle, repeat the cycle.
NOTE: A Bake or
Broil function
cannot be programmed before the
door
autornaticall.y
unlocks.
If “F-” and a number flash
on display and the control
beeps, this indicates function
error code.
Press
CLEAIVOFF
pad.
Allow oven to cool for one
hour. Put oven back into
operation. If function error
code repeats, disconnect power
to the oven and call for service.
(continued next page)
19