Filter
Top Products
12
Tools
Required
• Tinsnips to cut banding
• Stepladder
• 1-1/4″ open-end
wrench
• Bucket
• Level
• Appliance Hand Truck
• Tubing cutter
• 7/16″ open-end wrench
• #2 Phillips screwdriver
• Stubby Phillips
screwdriver
• Drill and appropriate bits
• 7/16″ socket with
3″ extension for
ratchet
• Safety glasses
Materials
Required
Hardware
Supplied
Flooring
• 1/4-1/4 union with nuts
• Anti-Tip Mounting Brackets
• Water shut-off valve
• Water filter WR97X0214
(optional but recommended)
• Custom panel for door and grille panel
• 1/4″ Copper water line tubing or GE SmartConnect
™
Tubing Kit
For proper installation, the refrigerator or freezer
must be placed on a level surface of hard material
the same height as the rest of the flooring. The floor
should be strong enough to support a fully loaded
refrigerator or freezer, or approximately 1,200 lbs.
NOTE: Protect the finish of the flooring. Cut a large
section of the cardboard carton and place under the
product where you are working.
Grounding the
Refrigerator
When disconnecting the power cord from the
adapter, always hold the adapter in place with one
hand and pull the power cord with the other hand.
If this is not done, the adapter ground terminal is
very likely to break with repeated use.
Should the adapter ground terminal break, DO NOT
USE the appliance until a proper ground has again
been established.
Use of Extension Cords
Because of potential safety hazards under certain
conditions, we strongly recommend against the use
of an extension cord. However, if you still elect to use
an extension cord, it is absolutely necessary that it
be a UL listed 3-wire grounding type appliance
extension cord having a grounding type plug and
outlet and that the electrical rating of the cord be
15 amperes (minimum) and 120 volts.
IMPORTANT – (Please read carefully)
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE
PROPERLY GROUNDED.
The power cord of these appliances is equipped with
a three-prong (grounding) plug which mates with a
standard three-prong (grounding) wall receptacle to
minimize the possibility of electric shock hazard from
this appliance.
Have the wall outlet and circuit checked by a
qualified electrician to make sure the outlet is
properly grounded.
Where a standard 2-prong wall outlet is encountered,
it is your personal responsibility and obligation to
have it replaced with a properly grounded 3-prong
wall outlet.
IMPORTANT:
We recommend two separate 115V, 60Hz. 20 amp.,
properly grounded electrical outlets for a side by
side installation of two products. Each electrical
outlet should have a voltage rating that matches
the rating plate.
DO NOT, UNDER ANY
CIRCUMSTANCES, CUT
OR REMOVE THE THIRD
(GROUND) PRONG
FROM THE POWER CORD.
Use of Adapter plug
Because of potential hazards under certain
conditions, we strongly recommend against use
of an adapter plug. However, if you still elect to use
an adapter, where local codes permit, a TEMPORARY
CONNECTION, may be made to a properly grounded
2-prong wall outlet by use of a UL listed adapter
available at most hardware stores.
The larger slot in the adapter must be aligned with
the larger slot in the wall outlet to provide proper
polarity in the connection of the power cord.
• Stick-on hook and loop fastener strips for 1/4″ side
panels
• 35″ long 2x4 for Anti-Tip support
• Screws to secure refrigerator to cabinetry
FICHE D’ADAPTATION
(Fiches d’adaptation non permises au Canada)
Attaching the adapter ground terminal to a wall
outlet cover screw does not ground the appliance
unless the cover screw is metal, and not
insulated, and the wall outlet is grounded through
the house wiring. You should have the circuit
checked by a qualified electrician to make sure
the outlet is properly grounded.
CAUTION
PRUDENCE
Installation
36″ Refrigerators, Freezers