Hotpoint SCL 08 EB Oven User Manual


  Open as PDF
of 12
 
GB
5
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
Electrical connection
Ovens equipped with a three-pole power supply cable are
designed to operate with alternating current at the voltage
and frequency indicated on the data plate located on the
appliance(seebelow).
Fitting the power supply cable
1. Open the terminal board
by inserting a screwdriver
into the side tabs of the
cover. Use the screwdriver
as a lever by pushing it
downtoopenthecover(see
diagram).
2. Install the power supply
cable by loosening the
cable clamp screw and the
three wire contact screws
L-N- .
Connect the wires to the
corresponding terminals:
the Blue wire to the terminal
marked(N),theBrownwire
totheterminalmarked(L)
andtheYellow/Greenwire
to the terminal marked
(seediagram).
3. Secure the cable by fastening the clamp screw.
4. Close the cover of the terminal board.
Connecting the supply cable to the mains
Install a standardised plug corresponding to the load
indicatedonthedataplate(seetable).
The appliance must be directly connected to the mains using
an omnipolar switch with a minimum contact opening of 3
mm installed between the appliance and the mains. The
switch must be suitable for the charge indicated and must
complywithcurrentelectricalregulations(theearthingwire
mustnotbeinterruptedbytheswitch).Thesupplycable
must be positioned so that it does not come into contact
withtemperatureshigherthan50°Catanypoint(theback
paneloftheoven,forexample).
! The installer must ensure that the correct electrical
connection has been performed and that it is fully compliant
with safety regulations.
Before connecting the appliance to the power supply, make
sure that
• Theapplianceisearthedandtheplugiscompliantwith
the law.
• Thesocketcanwithstandthemaximumpowerofthe
appliance, which is indicated on the data plate.
• Thevoltageisintherangebetweenthevaluesindicated
on the data plate.
N
L
• Thesocketiscompatiblewiththeplugoftheappliance.
If the socket is incompatible with the plug, ask an
authorised technician to replace it. Do not use extension
cords or multiple sockets.
! Once the appliance has been installed, the power supply
cable and the electrical socket must be easily accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced by
authorisedtechniciansonly(seeAssistance).
! The manufacturer declines any liability should these
safety measures not be observed.
APPLIANCE SPECIFICATIONS
Dimensions*
width 43.5 cm
height 32,4 cm
depth 41.5 cm
Volume*
59 l
Dimensions**
width 45.5 cm
height 32,4 cm
depth 41.5 cm
Volume**
62 l
Electrical
connections
voltage: 230 - 240 V~ 50/60 Hz
(see data plate)
maximum power absorbed
2800-3000 W
ENERGY
LABEL
* Only for models with drawn rails.
** Only for models with wire rails.
Directive 2002/40/EC on the label
of electric ovens. Standard EN 50304
Energy consumption for Natural
convection - heating mode:
Convection mode
Declared energy consumption for
Forced convection Class - heating
mode:
Baking
This appliance conforms to the
following European Economic
Community directives:
- 2006/95/EEC of 12/12/06 (Low
Voltage) and subsequent
amendments;
- 2004/108/EEC of 15/12/04
(Electromagnetic Compatibility) and
subsequent amendments;
- 93/68/EEC of 22/07/93 and
subsequent amendments.
- 2002/96/EC and subsequent
amendments.
 previous next